LT1012IN8#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LT1012 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Elements | 1 |
| Operating Supply Current | 380μA |
| Slew Rate | 0.2V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 114 dB |
| Current - Input Bias | 25pA |
| Voltage - Supply, Single/Dual (±) | 2.4V~40V ±1.2V~20V |
| Input Offset Voltage (Vos) | 8μV |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Voltage Gain | 126.02dB |
| Power Supply Rejection Ratio (PSRR) | 114dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 20V |
| Low-Bias | YES |
| Micropower | YES |
| Neg Supply Voltage-Max (Vsup) | -20V |
| Nominal Gain Bandwidth Product | 1MHz |
| Height Seated (Max) | 3.937mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT1012IN8#PBF Overview
There is a 8-DIP (0.300, 7.62mm) case package that contains the instrumentation amplifiers. A General Purpose-type buffer amplifier is shown here. Upon delivery, op amp ic is packaged in a Tube case. It is estimated that there will be at least 8 terminations this year. In this case, there are 8 pins on the board. Please take in mind that this instrumentation amplifier should be run at 15V. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. 8 pins are included on the operational amplifiers. There is an input offset voltage of 8μV for this buffer op amp. This electrical part should be mounted using type Through Hole. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~85°C . You can run this op amp ic on 380μA . There should be no change in the voltage gain. For the operating supply voltage of the op amp ic, there is a rating of 1.
LT1012IN8#PBF Features
8 Pins
supply voltage of 15V
126.02dB voltage gain
LT1012IN8#PBF Applications
There are a lot of Linear Technology/Analog Devices LT1012IN8#PBF Instrumentational OP Amps applications.
- Vehicle electronics
- Signal amplification
- Logarithmic operation circuits
- Displayers for aircraft and air transportation control systems
- Test equipment
- Signal filtering
- Voltage regulation circuit
- Multimedia playback equipment
- Measurements of Wheatstone bridge
- Inverse/same-phase proportional circuit
