LT1012S8#TRPBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| Published | 2003 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 250 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LT1012 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Elements | 1 |
| Operating Supply Current | 380μA |
| Slew Rate | 0.2V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 110 dB |
| Current - Input Bias | 25pA |
| Voltage - Supply, Single/Dual (±) | 2.4V~40V ±1.2V~20V |
| Input Offset Voltage (Vos) | 8μV |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Voltage Gain | 126.02dB |
| Average Bias Current-Max (IIB) | 0.0005μA |
| Power Supply Rejection Ratio (PSRR) | 110dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 20V |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Neg Supply Voltage-Max (Vsup) | -20V |
| Nominal Gain Bandwidth Product | 1MHz |
| Length | 4.9025mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT1012S8#TRPBF Overview
There is a 8-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. An op amp of this type is a General Purpose-type. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. The number of terminations is approaching the 8 mark. There are a total of 8 pins on this op amp. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. It should be noted that this op amp is a type of Operational Amplifier device. 8 pins are located on the operational amplifiers. Regarding input offset voltage, buffer amplifier rates 8μV voltage. For this electrical component, Surface Mount is the recommended mounting type. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around 0°C~70°C . Operational amplifier can operate supply current at 380μA. There should be no change in the voltage gain. As a whole, there are 1 elements that make up this buffer amplifier. TAPE AND REEL is adopted to pack the instrumentation amplifier.
LT1012S8#TRPBF Features
8 Pins
supply voltage of 15V
126.02dB voltage gain
LT1012S8#TRPBF Applications
There are a lot of Linear Technology/Analog Devices LT1012S8#TRPBF Instrumentational OP Amps applications.
- Navigation
- Laptop
- Image computer boards
- Radar
- Subtraction operation circuits
- RF cable systems
- Professional videography
- High speed sample
- earphone
- Power transmission
