LT1013DD
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | LT1013 |
| Pin Count | 8 |
| Operating Supply Voltage | 22V |
| Power Supplies | 5/+-15V |
| Number of Channels | 2 |
| Operating Supply Current | 350μA |
| Nominal Supply Current | 1.1mA |
| Slew Rate | 0.4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 97 dB |
| Current - Input Bias | 15nA |
| Voltage - Supply, Single/Dual (±) | 4V~44V ±2V~22V |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 700 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.03μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.05μA |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Power | NO |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT1013DD Overview
Packaging for the buffer amplifier is in the form of a 8-SOIC (0.154, 3.90mm Width) case. An op amp of this type is a General Purpose-type. There is a Tube case that is delivered with the instrumentation amplifiers. A total of 8 terminations have been reported in the past few weeks. A total of 8 pins are located on this board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. A total of 8 pins are present on the instrumentation amplifier. In terms of input offset voltage, operational amplifier rates 200μV. For this electrical component, Surface Mount is the recommended mounting type. According to the manufacturer, this buffer op amp works well at 0°C~70°C , which is a good operating temperature. This op amp can operate from a supply current at 350μA. 120dB should remain the voltage gain. Op amp ic has 2 channels. The operating supply voltage of instrumentation amplifier is rated 22V voltage.
LT1013DD Features
8 Pins
supply voltage of 15V
120dB voltage gain
LT1013DD Applications
There are a lot of Texas Instruments LT1013DD Instrumentational OP Amps applications.
- Gaming industry
- Television
- Radar
- Automation control systems
- Instrumentation
- Laptop
- Fast A/D and D/A converters
- Switching amplifier
- Information processing
- Addition operation circuits
