LT1013DID
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~105°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | LT1013 |
| Pin Count | 8 |
| Operating Supply Voltage | 22V |
| Power Supplies | 5/+-15V |
| Number of Channels | 2 |
| Operating Supply Current | 350μA |
| Nominal Supply Current | 1.1mA |
| Max Supply Current | 1mA |
| Slew Rate | 0.4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 97 dB |
| Current - Input Bias | 15nA |
| Voltage - Supply, Single/Dual (±) | 4V~44V ±2V~22V |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 700 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.03μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.05μA |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Power | NO |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT1013DID Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. The instrumentation amplifier in this picture is of the General Purpose-type. The op amp is delivered to you in a Tube case. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are attached to buffer op amp. This linear amplifier should be powered by an 15V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. It has 8 pins that make up the linear amplifier. Regarding input offset voltage, buffer amplifier rates 200μV voltage. This electronic part is best mounted with type Surface Mount. The buffer amplifier functions well at -40°C~105°C as far as operating temperature is concerned. It is possible to operate this buffer amplifier from a supply current of 350μA . It is a member of the 120dB's 120dB family. There are 2 channels on the operational amplifiers. The operating supply voltage of instrumentation amplifier is rated 22V voltage.
LT1013DID Features
8 Pins
supply voltage of 15V
120dB voltage gain
LT1013DID Applications
There are a lot of Texas Instruments LT1013DID Instrumentational OP Amps applications.
- E-book readers
- Vehicle electronics
- High-frequency data acquisition systems
- pH (acidity)
- Division circuits
- Cinema or auditorium audio system
- Radar
- Computer workstations
- Ultrasound transducers
- Signal filtering
