LT1014DMDW
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | LT1014 |
| Pin Count | 16 |
| Operating Supply Voltage | 22V |
| Number of Channels | 4 |
| Operating Supply Current | 350μA |
| Nominal Supply Current | 2.2mA |
| Power Dissipation | 1.025W |
| Slew Rate | 0.4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 97 dB |
| Current - Input Bias | 12nA |
| Voltage - Supply, Single/Dual (±) | 4V~44V ±2V~22V |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 700 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.03μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | NO |
| Micropower | YES |
| Max Frequency | 1kHz |
| Bias Current-Max (IIB) @25C | 0.05μA |
| Programmable Power | NO |
| Dual Supply Voltage | 15V |
| Input Offset Current-Max (IIO) | 0.002μA |
| Height | 2.65mm |
| Length | 10.3mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT1014DMDW Overview
There is a 16-SOIC (0.295, 7.50mm Width) case package that contains the instrumentation amplifiers. General Purpose-type instrumentation amplifiers are used in this application. Upon delivery, op amp ic is packaged in a Tube case. During the past two weeks, there have been close to 16 terminations. In this case, there are 16 pins on the board. The linear amplifier should be run at 15V at all times, so please keep that in mind when using it. This particular linear amplifier is a type of Operational Amplifier device, to be precise. The buffer op amp includes 16 pins. Op amp rates 200μV as input offset voltage. This electrical part should be mounted using type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -55°C~125°C . As long as the supply current of the chip does not exceed 350μA, this op amp ic can operate. 120dB should remain the voltage gain. Op amp ic has 4 channels. The operating supply voltage of the buffer op amp is rated at 22V.
LT1014DMDW Features
16 Pins
supply voltage of 15V
120dB voltage gain
LT1014DMDW Applications
There are a lot of Texas Instruments LT1014DMDW Instrumentational OP Amps applications.
- Video data acquisition
- Digital cameras
- Biopotential
- Differentiator circuits
- Signal filtering
- Thermocouples
- Voltage regulation circuit
- Instrumentation
- E-book readers
- Hand-held batteries
