banner_page

LT1125ACN#PBF

8nA 112 dB Instrumentational OP Amps 0.035μA ±4V~18V LT1125 14 Pins 14-DIP (0.300, 7.62mm)


  • Manufacturer: Linear Technology/Analog Devices
  • Nocochips NO: 471-LT1125ACN#PBF
  • Package: 14-DIP (0.300, 7.62mm)
  • Datasheet: PDF
  • Stock: 783
  • Description: 8nA 112 dB Instrumentational OP Amps 0.035μA ±4V~18V LT1125 14 Pins 14-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status PRODUCTION (Last Updated: 2 weeks ago)
Mounting Type Through Hole
Package / Case 14-DIP (0.300, 7.62mm)
Surface Mount NO
Number of Pins 14
Operating Temperature 0°C~70°C
Packaging Tube
Published 2011
JESD-609 Code e3
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 14
ECCN Code EAR99
Terminal Finish Matte Tin (Sn)
Subcategory Operational Amplifier
Technology BIPOLAR
Terminal Position DUAL
Number of Functions 4
Supply Voltage 15V
Base Part Number LT1125
Pin Count 14
Number of Elements 4
Power Supplies +-15V
Operating Supply Current 2.3mA
Supply Current-Max 13mA
Slew Rate 4.5V/μs
Architecture VOLTAGE-FEEDBACK
Amplifier Type General Purpose
Common Mode Rejection Ratio 112 dB
Current - Input Bias 8nA
Voltage - Supply, Single/Dual (±) ±4V~18V
Input Offset Voltage (Vos) 25μV
Gain Bandwidth Product 12.5MHz
Neg Supply Voltage-Nom (Vsup) -15V
Unity Gain BW-Nom 12500 kHz
Voltage Gain 144.61dB
Average Bias Current-Max (IIB) 0.035μA
Power Supply Rejection Ratio (PSRR) 116dB
Low-Offset YES
Frequency Compensation YES
Supply Voltage Limit-Max 22V
Bias Current-Max (IIB) @25C 0.02μA
Neg Supply Voltage-Max (Vsup) -22V
Nominal Gain Bandwidth Product 12.5MHz
Height Seated (Max) 3.809mm
Radiation Hardening No
RoHS Status ROHS3 Compliant
Lead Free Lead Free

LT1125ACN#PBF Overview


There is a 14-DIP (0.300, 7.62mm) case package that contains the instrumentation amplifiers. The instrumentation amplifier in this picture is of the General Purpose-type. A Tube case is used for delivering the op amp. There is a growing number of terminations approaching the number of 14. There are a total of 14 pins on this op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. A total of 14 pins are present on the instrumentation amplifier. Regarding input offset voltage, op amp rates 25μV. Through Hole is the recommended mounting type for this linear amplifier. The buffer amplifier functions well at 0°C~70°C as far as operating temperature is concerned. In order for this instrumentation amplifier to operate, the supply current needs to be between 2.3mA and 10 . 144.61dB should remain the voltage gain. There are 4 elements in this buffer amplifier.

LT1125ACN#PBF Features


14 Pins
supply voltage of 15V
144.61dB voltage gain

LT1125ACN#PBF Applications


There are a lot of Linear Technology/Analog Devices LT1125ACN#PBF Instrumentational OP Amps applications.

  • Weak signal detection
  • Addition operation circuits
  • Multimedia playback equipment
  • High-frequency data acquisition systems
  • Band-stop filter
  • Radiation thermometry transducers
  • Vehicle electronics
  • Weighing systems
  • Hand-held batteries
  • Portable media players

Write a review

Note: HTML is not translated!
    Bad           Good