LT1167CS8-1#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 1 TΩ |
| Terminal Finish | Matte Tin (Sn) |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LT1167 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Elements | 3 |
| Number of Circuits | 1 |
| Operating Supply Current | 900μA |
| Slew Rate | 1.2V/μs |
| Amplifier Type | Instrumentation |
| Common Mode Rejection Ratio | 85 dB |
| Current - Input Bias | 80pA |
| Voltage - Supply, Single/Dual (±) | 4.6V~36V ±2.3V~18V |
| Output Current per Channel | 27mA |
| Input Offset Voltage (Vos) | 15μV |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Average Bias Current-Max (IIB) | 0.0006μA |
| Power Supply Rejection Ratio (PSRR) | 100dB |
| Supply Voltage Limit-Max | 20V |
| Voltage - Input Offset | 20μV |
| -3db Bandwidth | 1MHz |
| Neg Supply Voltage-Max (Vsup) | -20V |
| Nominal Gain Bandwidth Product | 1MHz |
| Input Offset Current-Max (IIO) | 0.00055μA |
| Voltage Gain-Min | 1 |
| Voltage Gain-Nom | 10 |
| Length | 4.9mm |
| RoHS Status | ROHS3 Compliant |
LT1167CS8-1#PBF Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. A Instrumentation-type buffer amplifier is shown here. Linear amplifier is delivered in a Tube case. There is a growing number of terminations approaching the number of 8. There are a total of 8 pins on this op amp. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. There are 8 pins on this chip. As far as the input offset voltage is concerned, linear amplifier rates at 15μV. For this electronic part, it is recommended that you mount it with type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than 0°C~70°C for optimal performance. In order for this instrumentation amplifier to operate, the supply current needs to be between 900μA and 10 . On this buffer amplifier, there are 1 circuits. The op amp is rated for an operating supply voltage of 3. To conduct electronic part voltage gain higher than 1. Instrumentation amplifier resistance should stay within the range of 1 TΩ.
LT1167CS8-1#PBF Features
8 Pins
supply voltage of 15V
Resistance of 1 TΩ
LT1167CS8-1#PBF Applications
There are a lot of Linear Technology/Analog Devices LT1167CS8-1#PBF Instrumentational OP Amps applications.
- Vehicle electronics
- Addition operation circuits
- Signal amplification
- Fission chambers
- Division circuits
- Polarized electrodes
- Power control
- Logarithmic operation circuits
- Multiplication circuits
- High gain DC amplifier
