LT1167CS8#TRPBF
| Parameters | |
|---|---|
| Number of Circuits | 1 |
| Operating Supply Current | 900μA |
| Slew Rate | 1.2V/μs |
| Amplifier Type | Instrumentation |
| Common Mode Rejection Ratio | 85 dB |
| Current - Input Bias | 80pA |
| Voltage - Supply, Single/Dual (±) | 4.6V~36V ±2.3V~18V |
| Output Current per Channel | 27mA |
| Input Offset Voltage (Vos) | 15μV |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Average Bias Current-Max (IIB) | 0.0006μA |
| Power Supply Rejection Ratio (PSRR) | 100dB |
| Supply Voltage Limit-Max | 20V |
| Voltage - Input Offset | 20μV |
| -3db Bandwidth | 1MHz |
| Neg Supply Voltage-Max (Vsup) | -20V |
| Nominal Gain Bandwidth Product | 1MHz |
| Input Offset Current-Max (IIO) | 0.00055μA |
| Voltage Gain-Min | 1 |
| Voltage Gain-Nom | 10 |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 1 TΩ |
| Terminal Finish | Matte Tin (Sn) |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LT1167 |
| Pin Count | 8 |
| Number of Elements | 3 |
LT1167CS8#TRPBF Overview
Packaging for the buffer amplifier is in the form of a 8-SOIC (0.154, 3.90mm Width) case. The instrumentation amplifier in this picture is of the Instrumentation-type. A Tape & Reel (TR) case is used for delivering the op amp. A total of 8 terminations have been reported in the past few weeks. A total of 8 pins are located on this board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. The op amp ic has an array of 8 pins on it. Regarding input offset voltage, op amp rates 15μV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about 0°C~70°C . It is possible to operate this buffer amplifier from a supply current of 900μA . There are 1 circuits on this op amp. There are 3 elements in total in this linear amplifier. To conduct electronic part voltage gain higher than 1. It is important that the linear amplifier resistance stays within the range of 1 TΩ.
LT1167CS8#TRPBF Features
8 Pins
supply voltage of 15V
Resistance of 1 TΩ
LT1167CS8#TRPBF Applications
There are a lot of Linear Technology/Analog Devices LT1167CS8#TRPBF Instrumentational OP Amps applications.
- Proportional operation circuits
- Information processing
- High gain DC amplifier
- Power control
- Thermocouples
- Automotive sensors
- earphone
- Signal transformation
- Radiation thermometry transducers
- Micro signal measurement
