LT1179SW#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 4 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LT1179 |
| Pin Count | 16 |
| Operating Supply Voltage | 3V |
| Power Supplies | 5/+-15V |
| Number of Channels | 4 |
| Operating Supply Current | 17μA |
| Max Supply Current | 84μA |
| Slew Rate | 0.04V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 3nA |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±2.5V~15V |
| Input Offset Voltage (Vos) | 600μV |
| Bandwidth | 85 kHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 85 kHz |
| Voltage Gain | 116.9dB |
| Average Bias Current-Max (IIB) | 0.007μA |
| Power Supply Rejection Ratio (PSRR) | 92dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 22V |
| Voltage - Input Offset | 160μV |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.006μA |
| Dual Supply Voltage | 3V |
| Height | 2.34mm |
| Length | 10.49mm |
| Width | 7.6mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT1179SW#PBF Overview
In the package, you will find a 16-SOIC (0.295, 7.50mm Width)-case to contain the op amp ic. General Purpose-type instrumentation amplifiers are used in this application. A Tube case is used to deliver the buffer op amp. It is estimated that there will be 16 terminations in the next few months. Linear amplifier has a total of 16 pins. It is important to remember that this op amp should be operated at a voltage of 15V volts. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. The op amp ic has an array of 16 pins on it. In terms of input offset voltage, operational amplifier rates 600μV. For this electronic part, it is recommended that you mount it with type Surface Mount. With regard to operating temperature, this op amp functions well at 0°C~70°C. An 17μA volt supply current is needed for this linear amplifier to operate. 116.9dB should be the voltage gain. The op amp ic has 4 channels on it. The operating supply voltage of the buffer op amp is rated at 3V.
LT1179SW#PBF Features
16 Pins
supply voltage of 15V
116.9dB voltage gain
LT1179SW#PBF Applications
There are a lot of Linear Technology/Analog Devices LT1179SW#PBF Instrumentational OP Amps applications.
- Communication device
- Wireless base stations
- Inverse/same-phase proportional circuit
- Switching amplifier
- Micro signal measurement
- Signal filtering
- Signal transformation
- Medical instruments
- Signal amplification
- High speed sample
