LT1369CS#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2010 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LT1369 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Elements | 4 |
| Power Supplies | 3/5/+-15V |
| Number of Circuits | 4 |
| Operating Supply Current | 370μA |
| Max Supply Current | 2.08mA |
| Slew Rate | 0.065V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 77 dB |
| Current - Input Bias | 10nA |
| Voltage - Supply, Single/Dual (±) | 1.8V~30V ±0.9V~15V |
| Output Current per Channel | 75mA |
| Input Offset Voltage (Vos) | 150μV |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 160 kHz |
| Voltage Gain | 126.02dB |
| Power Supply Rejection Ratio (PSRR) | 90dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 200μV |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.035μA |
| Nominal Gain Bandwidth Product | 160 kHz |
| Height | 1.5mm |
| Length | 8.74mm |
| Width | 3.99mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT1369CS#PBF Overview
The linear amplifier is packaged in a 14-SOIC (0.154, 3.90mm Width) case which makes it easy for the consumer to handle. The instrumentation amplifier in this picture is of the General Purpose-type. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. The number of terminations is approaching the 14 mark. A total of 14 pins are located on this board. It is important to remember that this op amp should be operated at a voltage of 15V volts. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 14 pins are available on the instrumentation amplifier. In terms of input offset voltage, operational amplifier rates 150μV. For this electrical component, Surface Mount is the recommended mounting type. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around 0°C~70°C . As long as the supply current of the chip does not exceed 370μA, this op amp ic can operate. Keeping the voltage gain at 126.02dB is the best course of action. During the manufacturing process, this buffer amplifier is divided into 4 circuits. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 4. The operating supply voltage of the buffer op amp is rated at 3V.
LT1369CS#PBF Features
14 Pins
supply voltage of 15V
126.02dB voltage gain
Output Type: Rail-to-Rail
LT1369CS#PBF Applications
There are a lot of Linear Technology/Analog Devices LT1369CS#PBF Instrumentational OP Amps applications.
- Information processing
- Mobile phone
- Signal transformation
- Measurements of Wheatstone bridge
- Power control
- Polarized electrodes
- Vehicle electronics
- High-frequency data acquisition systems
- High/low-pass filter circuit
- Precision measurement
