LT1490ACMS8#TRPBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| Series | Over-The-Top® |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LT1490 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5/+-15V |
| Number of Circuits | 2 |
| Operating Supply Current | 50μA |
| Supply Current-Max | 0.17mA |
| Slew Rate | 0.07V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 1nA |
| Voltage - Supply, Single/Dual (±) | 2V~44V ±1V~22V |
| Output Current per Channel | 25mA |
| Input Offset Voltage (Vos) | 250μV |
| Gain Bandwidth Product | 200kHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 200 kHz |
| Voltage Gain | 123.52dB |
| Power Supply Rejection Ratio (PSRR) | 84dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0003μA |
| Programmable Power | NO |
| Wideband | NO |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT1490ACMS8#TRPBF Overview
A 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case is used to package the op amp. This is a General Purpose type op amp. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. There is a growing number of terminations approaching the number of 8. In this case, there are 8 pins on the board. I would like to remind you that this buffer op amp should be powered by an 15V battery. It should be noted that this op amp is a type of Operational Amplifier device. The buffer op amp includes 8 pins. As far as the input offset voltage is concerned, linear amplifier rates at 250μV. Surface Mount is the recommended mounting type for this linear amplifier. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of 0°C~70°C . As long as the supply current of the chip does not exceed 50μA, this op amp ic can operate. There should be no change in the voltage gain at 123.52dB. A instrumentation amplifier like this has 2 circuits. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. This linear amplifier pack is based on the TAPE AND REEL axis. Over-The-Top? corresponds to linear amplifier's series.
LT1490ACMS8#TRPBF Features
8 Pins
supply voltage of 15V
123.52dB voltage gain
Output Type: Rail-to-Rail
LT1490ACMS8#TRPBF Applications
There are a lot of Linear Technology/Analog Devices LT1490ACMS8#TRPBF Instrumentational OP Amps applications.
- Portable media players
- Communication
- Industrial applications including automation
- Signal amplification
- Signal operation
- Division circuits
- Displayers for aircraft and air transportation control systems
- single/dual op amp sum and difference circuits
- Portable electronic products powered by batteries
- Vehicle electronics
