banner_page

LT1490IN8#PBF

25mA per Channel 4nA 84 dB Instrumentational OP Amps 2V~44V ±1V~22V LT1490 8 Pins 8-DIP (0.300, 7.62mm)


  • Manufacturer: Linear Technology/Analog Devices
  • Nocochips NO: 471-LT1490IN8#PBF
  • Package: 8-DIP (0.300, 7.62mm)
  • Datasheet: PDF
  • Stock: 584
  • Description: 25mA per Channel 4nA 84 dB Instrumentational OP Amps 2V~44V ±1V~22V LT1490 8 Pins 8-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status PRODUCTION (Last Updated: 1 week ago)
Mounting Type Through Hole
Package / Case 8-DIP (0.300, 7.62mm)
Surface Mount NO
Number of Pins 8
Operating Temperature -40°C~85°C
Packaging Tube
Published 2000
Series Over-The-Top®
JESD-609 Code e3
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
ECCN Code EAR99
Terminal Finish Matte Tin (Sn)
Subcategory Operational Amplifier
Technology BIPOLAR
Terminal Position DUAL
Peak Reflow Temperature (Cel) NOT SPECIFIED
Number of Functions 2
Supply Voltage 15V
Time@Peak Reflow Temperature-Max (s) NOT SPECIFIED
Base Part Number LT1490
Pin Count 8
Qualification Status Not Qualified
Output Type Rail-to-Rail
Number of Elements 2
Power Supplies 3/5/+-15V
Operating Supply Current 50μA
Supply Current-Max 0.17mA
Slew Rate 0.07V/μs
Architecture VOLTAGE-FEEDBACK
Amplifier Type General Purpose
Common Mode Rejection Ratio 84 dB
Current - Input Bias 4nA
Voltage - Supply, Single/Dual (±) 2V~44V ±1V~22V
Output Current per Channel 25mA
Input Offset Voltage (Vos) 110μV
Gain Bandwidth Product 200kHz
Neg Supply Voltage-Nom (Vsup) -15V
Unity Gain BW-Nom 200 kHz
Voltage Gain 123.52dB
Power Supply Rejection Ratio (PSRR) 84dB
Low-Offset NO
Frequency Compensation YES
Voltage - Input Offset 250μV
Low-Bias NO
Micropower YES
Programmable Power NO
Nominal Gain Bandwidth Product 180 kHz
Wideband NO
Height Seated (Max) 3.937mm
RoHS Status ROHS3 Compliant
Lead Free Lead Free

LT1490IN8#PBF Overview


Packaged in a 8-DIP (0.300, 7.62mm) case, the buffer op amp is ready to use. There are two types of operational amplifiers in this circuit. There is a Tube case that is delivered with the instrumentation amplifiers. It is estimated that there will be 8 terminations in the next few months. Buffer amplifier has a total of 8 pins on it. This linear amplifier should be powered by an 15V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. A total of 8 pins are present on the instrumentation amplifier. As far as the input offset voltage is concerned, linear amplifier rates at 110μV. This electronic part is recommended for mounting type Through Hole. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . You can run this op amp ic on 50μA . 123.52dB should be the voltage gain. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 2. Over-The-Top? is the number that corresponds to the series of the buffer op amp.

LT1490IN8#PBF Features


8 Pins
supply voltage of 15V
123.52dB voltage gain
Output Type: Rail-to-Rail

LT1490IN8#PBF Applications


There are a lot of Linear Technology/Analog Devices LT1490IN8#PBF Instrumentational OP Amps applications.

  • Instrumentation
  • Broadcasting
  • E-book readers
  • Tablets
  • Information processing
  • Blood pressure sensors
  • Weak signal detection
  • Portable electronic products powered by batteries
  • Power transmission
  • Car stereo

Write a review

Note: HTML is not translated!
    Bad           Good