LT1510IGN#PBF
| Parameters | |
|---|---|
| Terminal Finish | Matte Tin (Sn) |
| HTS Code | 8542.39.00.01 |
| Subcategory | Power Management Circuits |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 16V |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LT1510 |
| Pin Count | 16 |
| Output Voltage | 20V |
| Input Voltage-Nom | 16V |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 7V |
| Analog IC - Other Type | BATTERY CHARGE CONTROLLER |
| Output Current | 1.5A |
| Min Input Voltage | 7V |
| Control Mode | CURRENT-MODE |
| Max Input Voltage | 29V |
| Control Technique | PULSE WIDTH MODULATION |
| Supply Current-Max (Isup) | 4.5mA |
| Nominal Input Voltage | 28V |
| Switcher Configuration | SINGLE |
| Switching Frequency-Max | 220kHz |
| Fault Protection | Over Voltage |
| Battery Chemistry | Multi-Chemistry |
| Number of Cells | 12 |
| Current - Charging | Constant - Programmable |
| Battery Pack Voltage | 20V Max |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1998 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
LT1510IGN#PBF Overview
If you are looking for it in the Tube package, then you have found it.In order to make it more convenient, it has been included in the 16-SSOP (0.154, 3.90mm Width) package.A Surface Mount mounting type is assigned to the device.It is best to set the temperature to -40°C~85°C TA.In order to operate, the device relies on an analog IC named BATTERY CHARGE CONTROLLER.It is necessary to supply the device with Constant - Programmable current in order to charge it.It is possible to find the related parts to the base part number LT1510.As far as the terminations are concerned, there are 16.Battery pack voltage is 20V Max.With 16 pins on it, it has a very simple design.There are 16 pins necessary to make it work.If it runs off of a 16V battery, then it should be able to run continuously.This device can be operated at an input voltage of 30V without being damaged.A 20V output voltage provides high efficiency.There is a constant output current of 1.5A when it is operating.This device is a member of subcategory Power Management Circuits.This circuit can function at a low supply voltage, such as 7VV.It was determined during the design process that Vsup (maximum supply voltage) should be set to 4.5mA.Input voltage is limited to 7V volts at the lowest.The device is 16V input voltage.This device can accept voltages up to 0 volts as an input voltage.It is most common to find parts with 220kHz switching frequencies.
LT1510IGN#PBF Features
Battery pack voltage of 20V Max
Power Management Circuits subcategory
16-SSOP (0.154, 3.90mm Width) package
LT1510IGN#PBF Applications
There are a lot of Linear Technology/Analog Devices LT1510IGN#PBF Battery Chargers ICs applications.
- Automotive/electrical vehicle
- Industrial handhelds
- Smart cameras
- Industrial lighting
- Electric boat
- Conventional charge
- Portable speaker systems
- TV sticks
- Charging cradle for wearable devices
- Remote sensor
