LT1510IGN#TRPBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1998 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| HTS Code | 8542.39.00.01 |
| Subcategory | Power Management Circuits |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 16V |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LT1510 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Qualification Status | Not Qualified |
| Input Voltage-Nom | 16V |
| Power Supplies | 16V |
| Analog IC - Other Type | BATTERY CHARGE CONTROLLER |
| Input Voltage (Min) | 7.8V |
| Control Mode | CURRENT-MODE |
| Output Current-Max | 2A |
| Input Voltage (Max) | 28V |
| Control Technique | PULSE WIDTH MODULATION |
| Supply Current-Max (Isup) | 4.5mA |
| Switcher Configuration | SINGLE |
| Switching Frequency-Max | 220kHz |
| Fault Protection | Over Voltage |
| Battery Chemistry | Multi-Chemistry |
| Voltage - Supply (Max) | 28V |
| Current - Charging | Constant - Programmable |
| Charge Current - Max | 1.5A |
| Battery Pack Voltage | 20V Max |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
LT1510IGN#TRPBF Overview
There is an Tape & Reel (TR) package that contains it. It is contained in a package named 16-SSOP (0.154, 3.90mm Width).Mounting type is Surface Mount.It is recommended to set the temperature to -40°C~85°C TA for reliable performance.To operate the device, an analog IC called BATTERY CHARGE CONTROLLER is used.To charge the device, a current of Constant - Programmable is required.It is possible to find the related parts to the base part number LT1510.It contains a total of 16 terminations.For the battery pack, it is set to 20V Max.There are 16 pins on it, so it has a very simple design.A maximum charging current of 1.5A is recommended.In general, it is recommended to use devices with 28V maximum supply voltages.Battery voltage should be 16V.Devices in this category are classified as Power Management Circuits.There is 4.5mA voltage set in Vsup (maximum supply voltage).The part's power supply is set to a value of 16V.A 16V input voltage is applied to the device.There is a minimum input voltage of 7.8V volts.Parts with 220kHz switching frequencies are at most available.With this device, the maximum input voltage is 28V.
LT1510IGN#TRPBF Features
Battery pack voltage of 20V Max
Power Management Circuits subcategory
16-SSOP (0.154, 3.90mm Width) package
LT1510IGN#TRPBF Applications
There are a lot of Linear Technology/Analog Devices LT1510IGN#TRPBF Battery Chargers ICs applications.
- Painting boat
- Maintenance shops
- Instruments and meters
- Automotive electronics
- Industrial handhelds
- Energy harvesting
- TV sticks
- Opportunity charge
- Marine buoy lights
- PDAs
