LT1510IS#TRPBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1998 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| HTS Code | 8542.39.00.01 |
| Subcategory | Power Management Circuits |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 16V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LT1510 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Qualification Status | Not Qualified |
| Output Voltage | 2.465V |
| Input Voltage-Nom | 16V |
| Power Supplies | 16V |
| Analog IC - Other Type | BATTERY CHARGE CONTROLLER |
| Input Voltage (Min) | 8V |
| Control Mode | CURRENT-MODE |
| Output Current-Max | 2A |
| Input Voltage (Max) | 28V |
| Control Technique | PULSE WIDTH MODULATION |
| Supply Current-Max (Isup) | 4.5mA |
| Switcher Configuration | SINGLE |
| Switching Frequency-Max | 200kHz |
| Fault Protection | Over Voltage |
| Battery Chemistry | Multi-Chemistry |
| Voltage - Supply (Max) | 28V |
| Current - Charging | Constant - Programmable |
| Charge Current - Max | 1.5A |
| Battery Pack Voltage | 20V Max |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
LT1510IS#TRPBF Overview
There is a package Tape & Reel (TR) available.We've included it in the 16-SOIC (0.154, 3.90mm Width) package so that it's easier to use.The device is mounted with mounting type Surface Mount.A temperature setting of -40°C~85°C TA would be the best thing to do.In order to operate this device, an analog IC of BATTERY CHARGE CONTROLLER must be used.To charge the device, there is a requirement for Constant - Programmable current.The related parts of the base part number LT1510 can be found by following the order of the base part number.As you can see, it has 16 terminations in it.The battery pack is set to 20V Max when it comes to the battery.With 16 pins on it, it has a very simple design.In its maximum charging mode, the part charges at 1.5A.28V is the maximum supply voltage for the device.The battery would need to have a voltage of 16V for the device to work.As long as the output voltage is set to 2.465V, then there is a possibility of optimal efficiency being achieved.The device falls under the Power Management Circuits subcategory.It is set to 4.5mA for Vsup (maximum supply voltage).Regarding the power supply for the part, it is set to 16V.16V is the input voltage for the device.Input voltage must be at least 8V volts.There is a maximum of 200kHz switching frequency available for parts.There is 28V maximum input voltage for this device.
LT1510IS#TRPBF Features
Battery pack voltage of 20V Max
Power Management Circuits subcategory
16-SOIC (0.154, 3.90mm Width) package
LT1510IS#TRPBF Applications
There are a lot of Linear Technology/Analog Devices LT1510IS#TRPBF Battery Chargers ICs applications.
- Military equipment
- Drone
- Remote sensor
- Electrical Utility industry
- Painting boat
- Electricity bank
- Robot
- Electric vehicles
- Industrial handhelds
- Mobile lighting
