LT1637CDD#PBF
| Parameters | |
|---|---|
| Average Bias Current-Max (IIB) | 0.05μA |
| Power Supply Rejection Ratio (PSRR) | 90dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 22V |
| Micropower | YES |
| Neg Supply Voltage-Max (Vsup) | -22V |
| Length | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WFDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2007 |
| Series | Over-The-Top® |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LT1637 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Number of Circuits | 1 |
| Operating Supply Current | 230μA |
| Supply Current-Max | 0.37mA |
| Slew Rate | 0.4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 17nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~44V ±1.35V~22V |
| Output Current per Channel | 31.7mA |
| Input Offset Voltage (Vos) | 125μV |
| Bandwidth | 1MHz |
| Gain Bandwidth Product | 1.1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1100 kHz |
| Voltage Gain | 118.06dB |
LT1637CDD#PBF Overview
Op amp is packaged in 8-WFDFN Exposed Pad case. Op amps are General Purpose types of amplifier on the chip. The case in which buffer amplifier is delivered is called a Tube case. It is estimated that there will be 8 terminations in the next few months. A total of 8 pins are attached to buffer op amp. I would like to remind you that this buffer op amp should be powered by an 15V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 8 pins are included on the operational amplifiers. Op amp ic rates 125μV for input offset voltage. This electronic part is recommended for mounting type Surface Mount. The buffer amplifier functions well at 0°C~70°C as far as operating temperature is concerned. Using an 230μA supply current, this operational amplifier ics can be operated. 118.06dB should remain the voltage gain. The buffer amp consists of 1 circuits in total. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. This linear amplifier has a total of 1 elements. In this case, Over-The-Top? represents the instrumentation amplifiers' series number.
LT1637CDD#PBF Features
8 Pins
supply voltage of 15V
118.06dB voltage gain
Output Type: Rail-to-Rail
LT1637CDD#PBF Applications
There are a lot of Linear Technology/Analog Devices LT1637CDD#PBF Instrumentational OP Amps applications.
- High-frequency data acquisition systems
- Vehicle electronics
- Logarithmic operation circuits
- Broadcasting
- Fission chambers
- Navigation
- Home audio systems
- Medical instruments
- Band-pass filter
- Television
