LT1637CMS8#PBF
| Parameters | |
|---|---|
| Base Part Number | LT1637 |
| Pin Count | 8 |
| JESD-30 Code | S-PDSO-G8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Circuits | 1 |
| Current - Supply | 230μA |
| Slew Rate | 0.4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 110 dB |
| Current - Input Bias | 17nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~44V ±1.35V~22V |
| Gain Bandwidth Product | 1.1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1100 kHz |
| Average Bias Current-Max (IIB) | 0.05μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 22V |
| Voltage - Input Offset | 100μV |
| Current - Output / Channel | 31.7mA |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.05μA |
| Programmable Power | NO |
| Neg Supply Voltage-Max (Vsup) | -22V |
| Wideband | NO |
| Power | NO |
| Voltage Gain-Min | 50000 |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2007 |
| Series | Over-The-Top® |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
LT1637CMS8#PBF Overview
Op amp is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case. A General Purpose-type buffer amplifier is shown here. Linear amplifier is delivered in a Tube case. During the past two weeks, there have been close to 8 terminations. The pins on this board total to 8 in total. I would like to remind you that this buffer op amp should be powered by an 15V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. For this electronic part, it is recommended that you mount it with type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about 0°C~70°C . This op amp ic has 1 circuits. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. In order to ensure optimal performance, an 230μA supply is recommended for this electrical component. This buffer amplifier is assigned within the Over-The-Top? series by its manufacturer. It is necessary to keep in mind that this instrumentation amplifier is able to conduct a minimum voltage gain of 50000.
LT1637CMS8#PBF Features
8 Pins
supply voltage of 15V
Output Type: Rail-to-Rail
LT1637CMS8#PBF Applications
There are a lot of Linear Technology/Analog Devices LT1637CMS8#PBF Instrumentational OP Amps applications.
- Subtraction operation circuits
- Mobile phone
- Laptop
- Power generator
- Home audio systems
- ECG equipment
- Addition operation circuits
- Multiplication circuits
- Large motor controllers
- Multimedia playback equipment
