LT1637CN8#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2007 |
| Series | Over-The-Top® |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LT1637 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Operating Supply Current | 230μA |
| Supply Current-Max | 0.37mA |
| Slew Rate | 0.4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 17nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~44V ±1.35V~22V |
| Output Current per Channel | 31.7mA |
| Input Offset Voltage (Vos) | 350μV |
| Gain Bandwidth Product | 1.1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1100 kHz |
| Voltage Gain | 118.06dB |
| Average Bias Current-Max (IIB) | 0.05μA |
| Power Supply Rejection Ratio (PSRR) | 90dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 22V |
| Voltage - Input Offset | 100μV |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.05μA |
| Programmable Power | NO |
| Neg Supply Voltage-Max (Vsup) | -22V |
| Nominal Gain Bandwidth Product | 1MHz |
| Wideband | NO |
| Height Seated (Max) | 3.937mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT1637CN8#PBF Overview
The linear amplifier is packaged in a 8-DIP (0.300, 7.62mm) case. This is a General Purpose type op amp. There is a Tube case that is delivered with the instrumentation amplifiers. During the past two weeks, there have been close to 8 terminations. Buffer amplifier has a total of 8 pins. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. There are 8 pins on this chip. The input offset voltage is 350μV. This electrical part should be mounted using type Through Hole. In relation to the operating temperature of this buffer op amp, it works well at an average of 0°C~70°C . Using an 230μA supply current, this operational amplifier ics can be operated. There should be no change in the voltage gain. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. There is a rating of 1 for the operating supply voltage of the buffer op amp. Buffer op amp series numbers are indicated by the Over-The-Top?.
LT1637CN8#PBF Features
8 Pins
supply voltage of 15V
118.06dB voltage gain
Output Type: Rail-to-Rail
LT1637CN8#PBF Applications
There are a lot of Linear Technology/Analog Devices LT1637CN8#PBF Instrumentational OP Amps applications.
- High-frequency data acquisition systems
- Ultrasound transducers
- Commercial audio systems
- Television broadcasting equipment
- Fast A/D and D/A converters
- Automotive sensors
- Vehicle electronics
- Industrial applications including automation
- Addition operation circuits
- Weak signal detection
