LT1783HS5#TRMPBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 months ago) |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-5 Thin, TSOT-23-5 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| Published | 2008 |
| Series | Over-The-Top® |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 250 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LT1783 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Operating Supply Current | 230μA |
| Slew Rate | 0.45V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 40nA |
| Voltage - Supply, Single/Dual (±) | 2.5V~18V ±1.25V~9V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 800μV |
| Bandwidth | 1.3MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 1300 kHz |
| Voltage Gain | 123.52dB |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 9V |
| Voltage - Input Offset | 500μV |
| Low-Bias | NO |
| Micropower | YES |
| Programmable Power | NO |
| Neg Supply Voltage-Max (Vsup) | -9V |
| Nominal Gain Bandwidth Product | 1.25MHz |
| Length | 2.9mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT1783HS5#TRMPBF Overview
Packaged in a SOT-23-5 Thin, TSOT-23-5 case, the buffer op amp is ready to use. This is a General Purpose type op amp. Instrumentation amplifier is delivered in a Cut Tape (CT) case. The number of terminations is approaching the 5 mark. Buffer amplifier has a total of 5 pins on it. It is important to remember that this op amp should be operated at a voltage of 5V volts. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. There are 5 pins on this chip. With regards to the offset voltage of the input, buffer amplifier is rated at 800μV. For this electronic part, it is recommended that you mount it with type Surface Mount. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. A supply current of 230μA can be used to operate this linear amplifier. There should be no change in the voltage gain. On the buffer amps, there are 1 channels that can be used. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. As a result of this, the buffer amplifier is packed in TAPE AND REEL. In this case, Over-The-Top? represents the instrumentation amplifiers' series number.
LT1783HS5#TRMPBF Features
5 Pins
supply voltage of 5V
123.52dB voltage gain
Output Type: Rail-to-Rail
LT1783HS5#TRMPBF Applications
There are a lot of Linear Technology/Analog Devices LT1783HS5#TRMPBF Instrumentational OP Amps applications.
- Inverse/same-phase proportional circuit
- Integrator circuits
- Division circuits
- Micro signal measurement
- Professional videography
- RF cable systems
- Instrumentation
- Exponential operation circuits
- Communication device
- Fission chambers
