Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 3 months ago) |
Mounting Type |
Through Hole |
Package / Case |
8-DIP (0.300, 7.62mm) |
Surface Mount |
NO |
Number of Pins |
8 |
Operating Temperature |
0°C~70°C |
Packaging |
Tube |
Published |
1999 |
JESD-609 Code |
e3 |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Operational Amplifier |
Terminal Position |
DUAL |
Peak Reflow Temperature (Cel) |
NOT SPECIFIED |
Number of Functions |
1 |
Supply Voltage |
15V |
Terminal Pitch |
2.54mm |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Base Part Number |
LT1792 |
Pin Count |
8 |
Qualification Status |
Not Qualified |
Number of Elements |
1 |
Number of Circuits |
1 |
Operating Supply Current |
4.2mA |
Slew Rate |
3.4V/μs |
Amplifier Type |
J-FET |
Common Mode Rejection Ratio |
82 dB |
Current - Input Bias |
300pA |
Voltage - Supply, Single/Dual (±) |
±4.5V~20V |
Input Offset Voltage (Vos) |
600μV |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Unity Gain BW-Nom |
4500 kHz |
Voltage Gain |
133.06dB |
Power Supply Rejection Ratio (PSRR) |
83dB |
Supply Voltage Limit-Max |
20V |
Voltage - Input Offset |
200μV |
Neg Supply Voltage-Max (Vsup) |
-20V |
Nominal Gain Bandwidth Product |
5.6MHz |
Height Seated (Max) |
3.937mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
LT1792CN8#PBF Overview
A 8-DIP (0.300, 7.62mm) case is used to package the op amp. There are two types of operational amplifiers in this circuit. A Tube case is used for delivering the op amp. There have been a total of 8 terminations over the past year. There are a total of 8 pins on this op amp. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 8 pins are available on the instrumentation amplifier. Regarding input offset voltage, buffer amplifier rates 600μV voltage. Through Hole is the recommended mounting type of operational amplifiers. According to the manufacturer, this buffer op amp works well at 0°C~70°C , which is a good operating temperature. As long as the supply current of the chip does not exceed 4.2mA, this op amp ic can operate. It is recommended to keep the voltage gain at 133.06dB at all times. A instrumentation amplifier like this has 1 circuits. As a whole, there are 1 elements that make up this buffer amplifier.
LT1792CN8#PBF Features
8 Pins
supply voltage of 15V
133.06dB voltage gain
LT1792CN8#PBF Applications
There are a lot of Linear Technology/Analog Devices LT1792CN8#PBF Instrumentational OP Amps applications.
- E-book readers
- Cinema or auditorium audio system
- Oscilloscopes
- Strain gauges
- Signal transformation
- Video conversion and routing
- Subtraction operation circuits
- Blood pressure sensors
- Ultrasound transducers
- Medical instruments