LT1795ISW#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 4 months ago) |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LT1795 |
| Pin Count | 20 |
| Power Supplies | +-5/+-15V |
| Number of Circuits | 2 |
| Operating Supply Current | 29mA |
| Supply Current-Max | 84mA |
| Slew Rate | 900V/μs |
| Amplifier Type | Current Feedback |
| Common Mode Rejection Ratio | 62 dB |
| Current - Input Bias | 10μA |
| Voltage - Supply, Single/Dual (±) | ±5V~15V |
| Output Current per Channel | 1A |
| Input Offset Voltage (Vos) | 13mV |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 50000 kHz |
| Low-Offset | NO |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 3mV |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Neg Supply Voltage-Max (Vsup) | -18V |
| Nominal Gain Bandwidth Product | 65MHz |
| Wideband | NO |
| Power | YES |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT1795ISW#PBF Overview
Packaged in a 20-SOIC (0.295, 7.50mm Width) case, the buffer op amp is ready to use. Buffer amps of this type are called Current Feedback-types. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. The number of terminations is approaching the 20 mark. In this case, there are 20 pins on the board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. 20 pins are located on the operational amplifiers. With regard to input offset voltage, instrumentation amplifier is rated at 13mV. Surface Mount is the recommended mounting type of operational amplifiers. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. Operational amplifier can operate supply current at 29mA. In total, there are 2 circuits on this buffer amplifier.
LT1795ISW#PBF Features
20 Pins
supply voltage of 15V
LT1795ISW#PBF Applications
There are a lot of Linear Technology/Analog Devices LT1795ISW#PBF Instrumentational OP Amps applications.
- Navigation
- High/low-pass filter circuit
- Power control
- Band-stop filter
- Large motor controllers
- Ultrasound transducers
- Vehicle electronics
- High speed sample
- Hand-held batteries
- Scintillation detectors
