Parameters |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Terminal Pitch |
0.95mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
LT1809 |
Pin Count |
6 |
Qualification Status |
Not Qualified |
Output Type |
Rail-to-Rail |
Number of Elements |
1 |
Power Supplies |
3/5/+-5V |
Operating Supply Current |
15mA |
Supply Current-Max |
25mA |
Slew Rate |
350V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
66 dB |
Current - Input Bias |
12.5μA |
Voltage - Supply, Single/Dual (±) |
2.5V~12.6V ±1.25V~6.3V |
Output Current per Channel |
85mA |
Input Offset Voltage (Vos) |
2.5mV |
Gain Bandwidth Product |
180MHz |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Unity Gain BW-Nom |
170000 kHz |
Voltage Gain |
98.06dB |
Power Supply Rejection Ratio (PSRR) |
71dB |
Low-Offset |
NO |
Frequency Compensation |
YES |
Voltage - Input Offset |
800μV |
Low-Bias |
NO |
-3db Bandwidth |
320MHz |
Programmable Power |
NO |
Nominal Gain Bandwidth Product |
160MHz |
Wideband |
YES |
Length |
2.9mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 2 weeks ago) |
Mounting Type |
Surface Mount |
Package / Case |
SOT-23-6 Thin, TSOT-23-6 |
Surface Mount |
YES |
Number of Pins |
6 |
Operating Temperature |
0°C~70°C |
Packaging |
Tape & Reel (TR) |
Published |
2009 |
JESD-609 Code |
e3 |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
6 |
ECCN Code |
EAR99 |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Operational Amplifier |
Packing Method |
TAPE AND REEL |
Technology |
BIPOLAR |
LT1809CS6#TRPBF Overview
It is packaged in an SOT-23-6 Thin, TSOT-23-6-case that protects the operational amplifiers from damage. General Purpose-type instrumentation amplifiers are used in this application. Linear amplifier is delivered in a Tape & Reel (TR) case. The number of terminations approaches 6. A total of 6 pins are attached to buffer op amp. This linear amplifier should be powered by an 5V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. There are 6 pins on this chip. With regards to the offset voltage of the input, buffer amplifier is rated at 2.5mV. The mounting type that is recommended for this electrical part is Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of 0°C~70°C . It is possible to operate this buffer amplifier from a supply current of 15mA . You should keep the voltage gain at 98.06dB for the time being. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. It is possible to count 1 elements on this buffer amplifier. For packing the buffer amplifier, the TAPE AND REEL-axis is adopted.
LT1809CS6#TRPBF Features
6 Pins
supply voltage of 5V
98.06dB voltage gain
Output Type: Rail-to-Rail
LT1809CS6#TRPBF Applications
There are a lot of Linear Technology/Analog Devices LT1809CS6#TRPBF Instrumentational OP Amps applications.
- Home audio systems
- Test equipment
- Instrumentation
- Scintillation detectors
- Band-pass filter
- Micro signal measurement
- Inverse/same-phase proportional circuit
- Large motor controllers
- Television broadcasting equipment
- Power control