LT1809IS6#TRMPBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 Thin, TSOT-23-6 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| Published | 2002 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 250 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LT1809 |
| Pin Count | 6 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 1 |
| Operating Supply Current | 15mA |
| Supply Current-Max | 25mA |
| Slew Rate | 350V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 12.5μA |
| Voltage - Supply, Single/Dual (±) | 2.5V~12.6V ±1.25V~6.3V |
| Output Current per Channel | 85mA |
| Input Offset Voltage (Vos) | 2.5mV |
| Bandwidth | 320MHz |
| Gain Bandwidth Product | 180MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 160000 kHz |
| Voltage Gain | 98.06dB |
| Power Supply Rejection Ratio (PSRR) | 71dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 800μV |
| Low-Bias | NO |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 160MHz |
| Length | 2.9mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT1809IS6#TRMPBF Overview
In order to protect the op amps, a SOT-23-6 Thin, TSOT-23-6 case is used. An op amp of this type is a General Purpose-type. In the case of Cut Tape (CT) cases, linear amplifier will be delivered. It is estimated that there will be 6 terminations in the next few months. It consists of a total of 6 pins in total. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. It has 6 pins that make up the linear amplifier. As far as the input offset voltage is concerned, linear amplifier rates at 2.5mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. An 15mA volt supply current is needed for this linear amplifier to operate. Op amp is a member of the 98.06dB's 98.06dB family. There are a total of 1 channels available on the op amps. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps.
LT1809IS6#TRMPBF Features
6 Pins
supply voltage of 5V
98.06dB voltage gain
Output Type: Rail-to-Rail
LT1809IS6#TRMPBF Applications
There are a lot of Linear Technology/Analog Devices LT1809IS6#TRMPBF Instrumentational OP Amps applications.
- E-book readers
- Displayers for aircraft and air transportation control systems
- Non-polarized electrodes
- Signal amplification
- Medical imaging
- Proportional operation circuits
- Communication device
- Active probe
- Computer workstations
- Portable docking station
