LT1813IDD#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WFDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 250 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LT1813 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Circuits | 2 |
| Operating Supply Current | 3mA |
| Supply Current-Max | 11mA |
| Slew Rate | 750V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 73 dB |
| Current - Input Bias | 900nA |
| Voltage - Supply, Single/Dual (±) | 2.5V~12.6V ±1.25V~6.3V |
| Output Current per Channel | 60mA |
| Input Offset Voltage (Vos) | 500μV |
| Gain Bandwidth Product | 100MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 100000 kHz |
| Voltage Gain | 66.02dB |
| Average Bias Current-Max (IIB) | 6μA |
| Power Supply Rejection Ratio (PSRR) | 78dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.3V |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 200MHz |
| Bias Current-Max (IIB) @25C | 4μA |
| Programmable Power | NO |
| Neg Supply Voltage-Max (Vsup) | -6.3V |
| Wideband | YES |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT1813IDD#PBF Overview
In the package, you will find a 8-WFDFN Exposed Pad-case to contain the op amp ic. An op amp of this type is a Voltage Feedback-type. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. During the past two weeks, there have been close to 8 terminations. In total, there are 8 pins on this op amp ic. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. Linear amplifier includes 8 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 500μV. This electronic part is recommended for mounting type Surface Mount. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~85°C . As long as the supply current of the chip does not exceed 3mA, this op amp ic can operate. There should be no change in the voltage gain at 66.02dB. In total, there are 2 circuits on this buffer amplifier.
LT1813IDD#PBF Features
8 Pins
supply voltage of 5V
66.02dB voltage gain
LT1813IDD#PBF Applications
There are a lot of Linear Technology/Analog Devices LT1813IDD#PBF Instrumentational OP Amps applications.
- Multimedia playback equipment
- Micro signal measurement
- Band-stop filter
- pH (acidity)
- Commercial audio systems
- Signal operation
- Weak signal detection
- Band-pass filter
- Test equipment
- Power transmission
