LT1994HDD#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WFDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 700kOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 250 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LT1994 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Operating Supply Current | 14.8mA |
| Nominal Supply Current | 13.3mA |
| Output Current | 85mA |
| Slew Rate | 65V/μs |
| Amplifier Type | Differential |
| Common Mode Rejection Ratio | 55 dB |
| Current - Input Bias | 18μA |
| Voltage - Supply, Single/Dual (±) | 2.375V~12.6V ±1.188V~6.3V |
| Output Current per Channel | 85mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 70MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 70000 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 3μA |
| Power Supply Rejection Ratio (PSRR) | 69dB |
| Supply Voltage Limit-Max | 6.3V |
| Voltage - Input Offset | 3mV |
| Neg Supply Voltage-Max (Vsup) | -6.3V |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
LT1994HDD#PBF Overview
The linear amplifier is packaged in a 8-WFDFN Exposed Pad case. An op amp of this type is a Differential-type. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. It is estimated that there will be at least 8 terminations this year. Buffer amplifier has a total of 8 pins. I would like to remind you that this buffer op amp should be powered by an 5V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. 8 pins are located on the operational amplifiers. The input offset voltage is 2mV. The mounting type that is recommended for this electrical part is Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. The buffer amplifier is capable of operating from a supply current of 14.8mA . The voltage gain should stay at 100dB. Op amp ic has 1 channels. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. During testing, the instrumentation amplifier resistance should remain within a range of 700kOhm.
LT1994HDD#PBF Features
8 Pins
supply voltage of 5V
100dB voltage gain
Output Type: Rail-to-Rail
Resistance of 700kOhm
LT1994HDD#PBF Applications
There are a lot of Linear Technology/Analog Devices LT1994HDD#PBF Instrumentational OP Amps applications.
- Navigation
- Displayers for aircraft and air transportation control systems
- Television broadcasting equipment
- Industrial control system
- Signal operation
- Multiplication circuits
- Vehicle electronics
- Oscilloscopes
- Scintillation detectors
- Power transmission
