LT1999CS8-50#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 months ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| ECCN Code | EAR99 |
| Resistance | 20MOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LT1999 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Number of Circuits | 1 |
| Operating Supply Current | 5.8mA |
| Slew Rate | 3V/μs |
| Amplifier Type | Current Sense |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 137.5μA |
| Voltage - Supply, Single/Dual (±) | 4.5V~5.5V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 1.2MHz |
| Voltage Gain | 34.02dB |
| Power Supply Rejection Ratio (PSRR) | 68dB |
| Supply Voltage Limit-Max | 6V |
| Nominal Gain Bandwidth Product | 2MHz |
| Number of Amplifiers | 2 |
| Length | 4.9mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
LT1999CS8-50#PBF Overview
There is a 8-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. A Current Sense-type buffer amplifier is shown here. In the case of Tube cases, linear amplifier will be delivered. In this case, there are 8 pins on the board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. The buffer op amp includes 8 pins. As far as the input offset voltage is concerned, linear amplifier rates at 500μV. Surface Mount is the recommended mounting type for this linear amplifier. According to the manufacturer, this buffer op amp works well at 0°C~70°C , which is a good operating temperature. In order for this instrumentation amplifier to operate, the supply current needs to be between 5.8mA and 10 . There should be no change in the voltage gain at 34.02dB. There are 1 circuits on op amps. The operating supply voltage of the buffer op amp is rated at 5V. It is important to keep the resistance within the 20MOhm range of the op amps. On the linear amplifier, there are 2 amplifiers.
LT1999CS8-50#PBF Features
8 Pins
supply voltage of 5V
34.02dB voltage gain
Resistance of 20MOhm
LT1999CS8-50#PBF Applications
There are a lot of Linear Technology/Analog Devices LT1999CS8-50#PBF Instrumentational OP Amps applications.
- earphone
- Vehicle electronics
- Commercial audio systems
- Industrial control system
- Hand-held batteries
- MP3
- High-frequency data acquisition systems
- Power transmission
- Division circuits
- Signal amplification
