LT3757AEMSE#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 months ago) |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LT3757 |
| Function | Step-Up, Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 7.2V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 24V |
| Analog IC - Other Type | SWITCHING REGULATOR |
| Output Configuration | Positive and Negative |
| Voltage - Supply (Vcc/Vdd) | 2.9V~40V |
| Control Features | Enable, Frequency Control, Soft Start |
| Input Voltage (Min) | 2.9V |
| Topology | Boost, Flyback, SEPIC |
| Control Mode | CURRENT-MODE |
| Output Current-Max | 0.02A |
| Frequency - Switching | 100kHz~1MHz |
| Input Voltage (Max) | 40V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Max Frequency | 1MHz |
| Clock Sync | Yes |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT3757AEMSE#PBF Overview
It comes in the 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) Exposed Pad package, which makes switching controller suitable for most applications. The dc motor controller is adquate to generate for 1 outputs. There is a Tube solid enclosure around the pmic. It is capable of dealing with Transistor Driver dc switching's output (s). dc switching'sVoltages 2.9V~40V are the dc control's supply voltage and operating voltage, respectively. Suitable for working in an dc switcher that has a -40°C~125°C TJ. The switching controller is capable of switching at the 100kHz~1MHz position. The Surface Mount allows it to be used for dc dc regulator in general. In order to control switching efficiently, the dcdc regulator features Enable, Frequency Control, Soft Start. An analog IC with the SWITCHING REGULATOR signal is connected to the switch converters. The switching converters's terminal (s) are designed at DUAL . Various 10 terminations. Some of the control techniques used by these dc dc converter ics are PULSE WIDTH MODULATION. DC switcher's input voltageis set to 24V. LT3757 can be used to locate other relevant dc to dc converter ics. 10 pins are on switching converter. Specifically, switching converter falls under the Switching Regulator or Controllers category. dc dc voltage regulators should have a minimum input voltage of 2.9V. Statistically, DC regulator outputs 7.2V volts. The dc to dc regulator can only accept a maximum input voltage of 40V. DC regulator1MHz has the maximum frequency. A value of 0.02A is output as the maximum value of current.
LT3757AEMSE#PBF Features
Transistor Driver Outputs
Switching Frequency: 100kHz~1MHz
Enable, Frequency Control, Soft Start
PULSE WIDTH MODULATION
LT3757AEMSE#PBF Applications
There are a lot of Linear Technology/Analog Devices LT3757AEMSE#PBF DC to DC converter applications.
- Thermal power
- Energy management systems
- Servo drive system
- Packaging
- Experimental setup
- Fire elevators
- Bending machines
- Automatic plug-in machines
- Product testing
- Geothermal power
