LT3782EFE
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-TSSOP (0.173, 4.40mm Width) Exposed Pad |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C |
| Published | 2009 |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 235 |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Function | Step-Up |
| Number of Outputs | 2 |
| Qualification Status | Not Qualified |
| Output Voltage | 72V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 13V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 4A |
| Voltage - Supply (Vcc/Vdd) | 6V~40V |
| Control Features | Enable, Reset, Soft Start |
| Input Voltage (Min) | 6V |
| Topology | Boost |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 154kHz~465kHz |
| Input Voltage (Max) | 40V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Switcher Configuration | PHASE-SHIFT |
| Duty Cycle (Max) | 94% |
| Length | 9.7mm |
| Width | 4.4mm |
| RoHS Status | Non-RoHS Compliant |
LT3782EFE Overview
The switching controller fits in the 28-TSSOP (0.173, 4.40mm Width) Exposed Pad package and is ideal for most applications. dc motor controller is suitable for 2 output generation. The system can process Transistor Driver dc switching's outputs (s). dc controls with 6V~40V voltage are supplied and operated. Work well in dc switchers with a -40°C~85°C. Switching can be done at 154kHz~465kHz with this switching controller. dc dc regulator can be generalized using Surface Mount. Featured in the dcdc regulator is Enable, Reset, Soft Start which allows efficient switching control. The switch converters are connected to an analog IC with a SWITCHING CONTROLLER output. There are a DUAL terminal on the switching converters. Various 28 terminations. PULSE WIDTH MODULATION is an example of one of the control techniques these dc dc converter ics adapt. There is a DC switcher's nominal voltage of 13V. Switching converter has a total of 28 pins. Specially, switching converter corresponds to type Switching Regulator or Controllers. 6V should be the minimum input voltage for the dc dc voltage regulator. DC regulator outputs 72V voltage based on test statistics. It should be fully noted that the dc to dc regulator only accepts 40V input voltage at most. You should note down the dc dc regulator's usual output current of 4A when you start a project. In most applications and prototype designs, DC switcher is qualified as a Surface Mount.
LT3782EFE Features
Transistor Driver Outputs
Switching Frequency: 154kHz~465kHz
Enable, Reset, Soft Start
PULSE WIDTH MODULATION
LT3782EFE Applications
There are a lot of Linear Technology/Analog Devices LT3782EFE DC to DC converter applications.
- Flaw detection equipment
- Magnetohydrodynamic power
- seismic instrument power circuits
- Radio equipment
- Hydraulic presses
- Grinders
- Smoke prevention equipment
- Solar power plants
- Mobile phones
- Wind power
