LT6002CDHC#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WFDFN Exposed Pad |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LT6002 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Power Supplies | 1.8/5V |
| Number of Circuits | 4 |
| Operating Supply Current | 20μA |
| Supply Current-Max | 0.096mA |
| Slew Rate | 0.018V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 68 dB |
| Current - Input Bias | 4nA |
| Voltage - Supply, Single/Dual (±) | 1.8V~16V ±0.9V~8V |
| Output Current per Channel | 10mA |
| Input Offset Voltage (Vos) | 500μV |
| Gain Bandwidth Product | 60kHz |
| Unity Gain BW-Nom | 50 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.01μA |
| Power Supply Rejection Ratio (PSRR) | 86dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Micropower | YES |
| Height Seated (Max) | 0.8mm |
| Length | 5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT6002CDHC#PBF Overview
There is a 16-WFDFN Exposed Pad case package that contains the instrumentation amplifiers. There are two types of operational amplifiers in this circuit. The op amp is delivered to you in a Tube case. A total of 16 terminations have been reported in the past few weeks. In this case, there are 16 pins on the board. Please take in mind that this instrumentation amplifier should be run at 1.8V. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. In total, the buffer amplifier consists of 16 pins. The input offset voltage is 500μV. The mounting type that is recommended for this electrical part is Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. It is possible to operate this buffer amplifier from a supply current of 20μA . Maintain 120dB as the voltage gain. During the manufacturing process, this buffer amplifier is divided into 4 circuits. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages.
LT6002CDHC#PBF Features
16 Pins
supply voltage of 1.8V
120dB voltage gain
Output Type: Rail-to-Rail
LT6002CDHC#PBF Applications
There are a lot of Linear Technology/Analog Devices LT6002CDHC#PBF Instrumentational OP Amps applications.
- Precision measurement
- Medical instruments
- Voltage regulation circuit
- Inverse/same-phase proportional circuit
- Oscilloscopes
- Power transmission
- Semiconductor detectors
- Integrator circuits
- High/low-pass filter circuit
- Communication device
