LT6011ACDD#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WFDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LT6011 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Power Supplies | 5/+-15V |
| Number of Circuits | 2 |
| Operating Supply Current | 260μA |
| Supply Current-Max | 0.76mA |
| Slew Rate | 0.11V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 107 dB |
| Current - Input Bias | 20pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~36V ±1.35V~18V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 35μV |
| Bandwidth | 350 kHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 350 kHz |
| Voltage Gain | 126.02dB |
| Average Bias Current-Max (IIB) | 0.00045μA |
| Power Supply Rejection Ratio (PSRR) | 112dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0003μA |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT6011ACDD#PBF Overview
There is a 8-WFDFN Exposed Pad case in which the instrumentation amplifier is packaged. This is a General Purpose type op amp. A Tube case is used for delivering the op amp. It is estimated that there will be 8 terminations in the next few months. Linear amplifier has a total of 8 pins. Please take in mind that op amp should be run at 15V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. There are 8 pins on this chip. There is an input offset voltage of 35μV for this buffer op amp. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of 0°C~70°C when it comes to operating temperatureAn 260μA volt supply current is needed for this linear amplifier to operate. Maintain 126.02dB as the voltage gain. During the manufacturing process, this buffer amplifier is divided into 2 circuits. On the output type, there are Rail-to-Rail different types of op amps.
LT6011ACDD#PBF Features
8 Pins
supply voltage of 15V
126.02dB voltage gain
Output Type: Rail-to-Rail
LT6011ACDD#PBF Applications
There are a lot of Linear Technology/Analog Devices LT6011ACDD#PBF Instrumentational OP Amps applications.
- Semiconductor detectors
- Video conversion and routing
- RF cable systems
- Oscilloscopes
- Strain gauges
- Exponential operation circuits
- Laptop
- Voltage regulation circuit
- Micro signal measurement
- Tablets
