LT6011CMS8#TRPBF

150pA 135 dB Instrumentational OP Amps 2.7V~36V ±1.35V~18V LT6011 8 Pins 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)

Manufacturer: Linear Technology/Analog Devices
Nocochips NO: 471-LT6011CMS8#TRPBF
Package: 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
Datasheet: PDF
Stock: 129
Description: 150pA 135 dB Instrumentational OP Amps 2.7V~36V ±1.35V~18V LT6011 8 Pins 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mounting Type	Surface Mount
Package / Case	8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
Surface Mount	YES
Operating Temperature	0°C~70°C
Packaging	Tape & Reel (TR)
Published	2012
JESD-609 Code	e3
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
ECCN Code	EAR99
Terminal Finish	Matte Tin (Sn)
Subcategory	Operational Amplifier
Packing Method	TAPE AND REEL
Technology	BIPOLAR
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	15V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	LT6011
Pin Count	8
JESD-30 Code	S-PDSO-G8
Qualification Status	Not Qualified
Output Type	Rail-to-Rail
Power Supplies	5/+-15V
Number of Circuits	2
Current - Supply	260μA
Slew Rate	0.11V/μs
Architecture	VOLTAGE-FEEDBACK
Amplifier Type	General Purpose
Common Mode Rejection Ratio	135 dB
Current - Input Bias	150pA
Voltage - Supply, Single/Dual (±)	2.7V~36V ±1.35V~18V
Gain Bandwidth Product	350kHz
Neg Supply Voltage-Nom (Vsup)	-15V
Unity Gain BW-Nom	350 kHz
Low-Offset	YES
Frequency Compensation	YES
Voltage - Input Offset	40μV
Current - Output / Channel	20mA
Low-Bias	YES
Micropower	YES
Bias Current-Max (IIB) @25C	0.0009μA
Height Seated (Max)	1.1mm
Length	3mm
RoHS Status	ROHS3 Compliant

LT6011CMS8#TRPBF Overview

It is packaged in an 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case that protects the operational amplifiers from damage. A General Purpose-type buffer amplifier is shown here. The op amp is delivered to you in a Tape & Reel (TR) case. In recent months, the number of terminations has approached 8. There are a total of 8 pins on this op amp. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. For this electronic part, it is recommended that you mount it with type Surface Mount. It is important to note that this linear amplifier works well at a temperature of 0°C~70°C when it comes to operating temperatureThis op amp ic has 2 circuits. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method. As a result, it is recommended that a power supply of 260μA be used with this electronic part.