LT6011IMS8#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LT6011 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Power Supplies | 5/+-15V |
| Number of Channels | 2 |
| Operating Supply Current | 260μA |
| Slew Rate | 0.11V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 107 dB |
| Current - Input Bias | 150pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~36V ±1.35V~18V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 60μV |
| Bandwidth | 330 kHz |
| Gain Bandwidth Product | 350kHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 350 kHz |
| Voltage Gain | 126.02dB |
| Average Bias Current-Max (IIB) | 0.0015μA |
| Power Supply Rejection Ratio (PSRR) | 112dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Voltage - Input Offset | 40μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0009μA |
| Nominal Gain Bandwidth Product | 330 kHz |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
LT6011IMS8#PBF Overview
In the package, you will find a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case to contain the op amp ic. Op amps are General Purpose types of amplifier on the chip. There is a Tube case that is delivered with the instrumentation amplifiers. The number of terminations approaches 8. It consists of a total of 8 pins in total. The linear amplifier should be run at 15V at all times, so please keep that in mind when using it. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. 8 pins are included on the operational amplifiers. With regards to the offset voltage of the input, buffer amplifier is rated at 60μV. This electronic part is recommended for mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureAs long as the supply current of the chip does not exceed 260μA, this op amp ic can operate. 126.02dB should be the voltage gain. Op amp ic has 2 channels. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals.
LT6011IMS8#PBF Features
8 Pins
supply voltage of 15V
126.02dB voltage gain
Output Type: Rail-to-Rail
LT6011IMS8#PBF Applications
There are a lot of Linear Technology/Analog Devices LT6011IMS8#PBF Instrumentational OP Amps applications.
- Large motor controllers
- Comparator
- Commercial audio systems
- Information processing
- Communication
- Active probe
- Signal filtering
- Displayers for aircraft and air transportation control systems
- Computer workstations
- Tablets
