LT6234IS8#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LT6234 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Power Supplies | 3.3/5/+-5V |
| Number of Circuits | 2 |
| Operating Supply Current | 1.15mA |
| Supply Current-Max | 3.5mA |
| Slew Rate | 17V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 1.5μA |
| Voltage - Supply, Single/Dual (±) | 3V~12.6V ±1.5V~6.3V |
| Output Current per Channel | 55mA |
| Input Offset Voltage (Vos) | 350μV |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 60000 kHz |
| Voltage Gain | 102.92dB |
| Average Bias Current-Max (IIB) | 4μA |
| Power Supply Rejection Ratio (PSRR) | 90dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.3V |
| Voltage - Input Offset | 50μV |
| Bias Current-Max (IIB) @25C | 3μA |
| Neg Supply Voltage-Max (Vsup) | -6.3V |
| Nominal Gain Bandwidth Product | 60MHz |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT6234IS8#PBF Overview
There is a 8-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. A General Purpose-type buffer amplifier is shown here. A Tube case is used to deliver the buffer op amp. A total of 8 terminations have been reported in the past few weeks. The pins on this board total to 8 in total. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. Instrumentation amplifier is a part of Operational Amplifier. 8 pins are located on the operational amplifiers. Op amp rates 350μV as input offset voltage. Surface Mount is the recommended mounting type of operational amplifiers. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureThis op amp can operate from a supply current at 1.15mA. There should be no change in the voltage gain at 102.92dB. There are 2 circuits on op amps. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. 2 elements make up the design of this buffer amplifier.
LT6234IS8#PBF Features
8 Pins
supply voltage of 5V
102.92dB voltage gain
Output Type: Rail-to-Rail
LT6234IS8#PBF Applications
There are a lot of Linear Technology/Analog Devices LT6234IS8#PBF Instrumentational OP Amps applications.
- RF cable systems
- PDA
- Large motor controllers
- Instrumentation
- Fast A/D and D/A converters
- Mobile phone
- Addition operation circuits
- Biopotential
- Video conversion and routing
- Voltage regulation circuit
