LT6237IMS8#PBF
| Parameters | |
|---|---|
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5/+-5V |
| Number of Circuits | 2 |
| Operating Supply Current | 3.3mA |
| Slew Rate | 70V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 115 dB |
| Current - Input Bias | 5μA |
| Voltage - Supply, Single/Dual (±) | 3V~12.6V ±1.5V~6.3V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 50μV |
| Bandwidth | 215MHz |
| Unity Gain BW-Nom | 200000 kHz |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Voltage - Input Offset | 50μV |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 90MHz |
| Bias Current-Max (IIB) @25C | 10μA |
| Programmable Power | NO |
| Power | NO |
| Voltage Gain-Min | 3600 |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2014 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 2 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LT6237 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
LT6237IMS8#PBF Overview
In order to protect the op amps, a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case is used. There are two types of operational amplifiers in this circuit. The op amp is delivered to you in a Tube case. It is estimated that there will be at least 8 terminations this year. In this case, there are 8 pins on the board. The linear amplifier should be run at 3.3V at all times, so please keep that in mind when using it. It should be noted that this op amp is a type of Operational Amplifier device. In total, the buffer amplifier consists of 8 pins. Op amp ic rates 50μV for input offset voltage. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. Operational amplifier can operate supply current at 3.3mA. This op amp ic has 2 circuits. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. The minimum voltage gain this buffer op amp is able to conduct is 3600.
LT6237IMS8#PBF Features
8 Pins
supply voltage of 3.3V
Output Type: Rail-to-Rail
LT6237IMS8#PBF Applications
There are a lot of Linear Technology/Analog Devices LT6237IMS8#PBF Instrumentational OP Amps applications.
- Weak signal detection
- High speed sample
- Home audio systems
- Signal amplification
- High gain DC amplifier
- Multimedia playback equipment
- Portable electronic products powered by batteries
- Automatic control
- Industrial applications including automation
- earphone
