LTC1702AIGN#TRPBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 24-SSOP (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LTC1702 |
| Function | Step-Down |
| Number of Outputs | 2 |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 5V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Voltage - Supply (Vcc/Vdd) | 3V~7V |
| Control Features | Current Limit, Enable, Power Good, Soft Start |
| Input Voltage (Min) | 3V |
| Topology | Buck |
| Control Mode | VOLTAGE-MODE |
| Output Current-Max | 5A |
| Frequency - Switching | 550kHz |
| Input Voltage (Max) | 7V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Switcher Configuration | PUSH-PULL |
| Duty Cycle (Max) | 90% |
| Clock Sync | No |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Width | 3.895mm |
| RoHS Status | ROHS3 Compliant |
LTC1702AIGN#TRPBF Overview
It comes in the 24-SSOP (0.154, 3.90mm Width) package, which makes switching controller suitable for most applications. There is enough capacity in the dc motor controller to generate the output for the 2 input. Tape & Reel (TR) solid enclosure protects the pmic. The system can process Transistor Driver dc switching's outputs (s). DC control operates at 3V~7V volts and has 3V~7V supply voltage. A -40°C~85°C TA dc switcher is not a problem. Switching can be done at 550kHz with this switching controller. The Surface Mount makes it ideal for general dc dc regulator. To provide efficient switching control, Current Limit, Enable, Power Good, Soft Start is included in the dcdc regulator. A SWITCHING CONTROLLER analog integrated circuit is connected to the switch converters. Terminal (s) of the switching converters are designed at the DUAL position. The 24 terminations can be used for a wide range of dc switching. This dc dc converter ic uses a variety of control techniques, including PULSE WIDTH MODULATION. The nominal DC switcher's voltage input is 5V. Searching "LTC1702" will return other relevant dc to dc converter ics. Switching converter type is specifically Switching Regulator or Controllers. Input voltage of dc dc voltage regulator should be 3V. A maximum voltage of 7V is accepted by the dc to dc regulator as an input voltage. Whenever the current value is 5A, switching converter outputs the highest possible value.
LTC1702AIGN#TRPBF Features
Transistor Driver Outputs
Switching Frequency: 550kHz
Current Limit, Enable, Power Good, Soft Start
PULSE WIDTH MODULATION
LTC1702AIGN#TRPBF Applications
There are a lot of Linear Technology/Analog Devices LTC1702AIGN#TRPBF DC to DC converter applications.
- Mobile phones
- Computed tomography (CT)
- Arc suppression circuits
- Current source circuits
- Handheld GPS
- Flaw detection equipment
- Domestic water pumps
- Low output voltage switching power supply circuits
- Smoke prevention equipment
- Printing
