LTC1735CGN#TRPBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | 0°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LTC1735 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 15V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Voltage - Supply (Vcc/Vdd) | 4V~30V |
| Control Features | Enable, Power Good, Soft Start |
| Input Voltage (Min) | 3.5V |
| Topology | Buck |
| Control Mode | CURRENT-MODE |
| Output Current-Max | 3A |
| Frequency - Switching | 300kHz |
| Input Voltage (Max) | 36V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Switcher Configuration | PUSH-PULL |
| Duty Cycle (Max) | 99.4% |
| Clock Sync | No |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
LTC1735CGN#TRPBF Overview
With its 16-SSOP (0.154, 3.90mm Width) package, the switching controller fits the needs of most applications. For 1 outputs, the dc motor controller is appropriate. The pmic is packaged in Tape & Reel (TR) solid enclosure. Transistor Driver dc switching's outputs (s) are supported. Voltages 4V~30V are the dc control's supply voltage and operating voltage, respectively. Worked in an dc switcher with a 0°C~85°C TA rating. The switching controller can be switched at 300kHz. As it has a Surface Mount value, it can be used for general dc dc regulator. The dcdc regulator features Enable, Power Good, Soft Start for efficient switching control. A SWITCHING CONTROLLER analog IC is connected to the switch converters. There are a DUAL terminal on the switching converters. A variety of 16 terminations are available in dc switching. Some of the control techniques adapted by these dc dc converter ics include PULSE WIDTH MODULATION. A DC switcher's nominal voltage of 15V is input. You can find other relevant dc to dc converter ics by searching "LTC1735". dc dc voltage regulators should have a minimum input voltage of 3.5V. It should be noted that the dc to dc regulator only accepts 36V voltage as input voltage. The output of this function is the greatest value of 3A.
LTC1735CGN#TRPBF Features
Transistor Driver Outputs
Switching Frequency: 300kHz
Enable, Power Good, Soft Start
PULSE WIDTH MODULATION
LTC1735CGN#TRPBF Applications
There are a lot of Linear Technology/Analog Devices LTC1735CGN#TRPBF DC to DC converter applications.
- Bending machines
- Wind power
- Flexible manufacturing cells
- Gear/thread machining machines
- Wide-range voltage regulation circuits
- Domestic water pumps
- Access control systems
- Planers
- Power supplies of electronic gadgets
- Grinders
