LTC1922IG-1#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 4 months ago) |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Surface Mount | YES |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2001 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | ALSO CONFIGURABLE IN CURRENT MODE |
| Subcategory | Switching Regulator or Controllers |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LTC1922 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Output Voltage | 5V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 9.5V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive, Isolation Capable |
| Output Current | 100A |
| Voltage - Supply (Vcc/Vdd) | 3.8V~10.3V |
| Control Features | Ramp, Soft Start |
| Topology | Full-Bridge |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | Up to 1MHz |
| Control Technique | PHASE-SHIFT CONTROL |
| Synchronous Rectifier | Yes |
| Switcher Configuration | PHASE-SHIFT |
| Max Frequency | 1MHz |
| Duty Cycle (Max) | 99% |
| Height Seated (Max) | 2mm |
| Length | 7.2mm |
| Width | 5.3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LTC1922IG-1#PBF Overview
Capsuled in the 20-SSOP (0.209, 5.30mm Width) package, the switching controller suits most application needs. dc motor controller is suitable for 1 output generation. There is a Tube solid enclosure around the pmic. It is capable of dealing with Transistor Driver dc switching's output (s). dc switching'sThe supply and operating voltage of the dc control are 3.8V~10.3V. A -40°C~85°C TA dc switcher is not a problem. With this switching controller, you can switch at Up to 1MHz. The Surface Mount value makes it suitable for general dc dc regulator. The dcdc regulator features Ramp, Soft Start for efficient switching control. The switch converters are connected to an analog IC with a SWITCHING CONTROLLER output. DUAL are the position of the terminal of the switching converters. A variety of 20 terminations are available in dc switching. These dc dc converter ics adapt a variety of control techniques, including PHASE-SHIFT CONTROL. DC switcher's input voltageis 9.5V volts. A search for "LTC1922" will reveal other relevant dc to dc converter ics. The switching converter has a total of 20 pins. There is a particular type of Switching Regulator or Controllers in switching converter. As determined by the test statistics, the output voltage of DC regulator is 5V. If you are starting a new project, you should note the dc dc regulator's typical output current is 100A. There is a maximum frequency of 1MHz on this dc regulators. The value of DC to DC voltage regulator is set to ALSO CONFIGURABLE IN CURRENT MODE in order to better satisfy the requirement.
LTC1922IG-1#PBF Features
Transistor Driver Outputs
Switching Frequency: Up to 1MHz
Ramp, Soft Start
PHASE-SHIFT CONTROL
ALSO CONFIGURABLE IN CURRENT MODE
LTC1922IG-1#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC1922IG-1#PBF DC to DC converter applications.
- Industrial robots
- Power supplies of electronic gadgets
- Energy management systems
- Series voltage regulation circuits
- PSRR circuits
- Lathes
- Electrical power transmission
- Sensitive electronic devices
- Post equipment
- SMT equipment
