LTC2050IS8#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LTC2050 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Operating Supply Current | 800μA |
| Max Supply Current | 1.2mA |
| Slew Rate | 2V/μs |
| Architecture | CHOPPER-STAB |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 75pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V |
| Input Offset Voltage (Vos) | 500nV |
| Bandwidth | 3MHz |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 140dB |
| Average Bias Current-Max (IIB) | 0.0003μA |
| Power Supply Rejection Ratio (PSRR) | 120dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 0.5μV |
| Low-Bias | YES |
| Nominal Gain Bandwidth Product | 3MHz |
| Height | 1.5mm |
| Length | 5mm |
| Width | 3.99mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LTC2050IS8#PBF Overview
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. A Zero-Drift-type buffer amplifier is shown here. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. We are approaching the 8h termination of the year. A total of 8 pins are attached to buffer op amp. I would like to remind you that this buffer op amp should be powered by an 3V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. Linear amplifier includes 8 pins. Regarding input offset voltage, op amp rates 500nV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. An 800μA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain at 140dB. Instrumentation amplifier has 1 channels on it. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. The operating supply voltage of instrumentation amplifier is rated 3V voltage.
LTC2050IS8#PBF Features
8 Pins
supply voltage of 3V
140dB voltage gain
Output Type: Rail-to-Rail
LTC2050IS8#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC2050IS8#PBF Instrumentational OP Amps applications.
- Inverse/same-phase proportional circuit
- pH (acidity)
- Signal amplification
- Portable electronic products powered by batteries
- Active probe
- Exponential operation circuits
- Automatic control
- E-book readers
- Automotive sensors
- Radiation thermometry transducers
