LTC2052HGN#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 250 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.635mm |
| Base Part Number | LTC2052 |
| Pin Count | 16 |
| Output Type | Rail-to-Rail |
| Number of Elements | 4 |
| Power Supplies | 3/5V |
| Number of Circuits | 4 |
| Operating Supply Current | 850μA |
| Supply Current-Max | 6mA |
| Slew Rate | 2V/μs |
| Architecture | CHOPPER-STAB |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 90pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~7V |
| Input Offset Voltage (Vos) | 500nV |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 140dB |
| Average Bias Current-Max (IIB) | 0.003μA |
| Power Supply Rejection Ratio (PSRR) | 120dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 1μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.000075μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 3MHz |
| Wideband | NO |
| Height Seated (Max) | 1.75mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LTC2052HGN#PBF Overview
A 16-SSOP (0.154, 3.90mm Width) case is used to package the op amp. The instrumentation amplifier in this picture is of the Zero-Drift-type. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. It is estimated that there will be at least 16 terminations this year. A total of 16 pins are attached to buffer op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 3V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. The op amp ic has an array of 16 pins on it. Regarding input offset voltage, buffer amplifier rates 500nV voltage. Surface Mount is the recommended mounting type for this linear amplifier. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . This op amp can operate from a supply current at 850μA. 140dB should be the voltage gain. On this buffer amplifier, there are 4 circuits. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. The buffer op amp is rated for an operating voltage of 4 when it comes to the power supply.
LTC2052HGN#PBF Features
16 Pins
supply voltage of 3V
140dB voltage gain
Output Type: Rail-to-Rail
LTC2052HGN#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC2052HGN#PBF Instrumentational OP Amps applications.
- Scintillation detectors
- Addition operation circuits
- Displayers for aircraft and air transportation control systems
- Strain gauges
- Subtraction operation circuits
- Measurements of Wheatstone bridge
- Automation control systems
- Television
- Comparator
- Mobile phone
