LTC2052HVHS#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 250 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LTC2052 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Elements | 4 |
| Number of Circuits | 4 |
| Operating Supply Current | 1mA |
| Supply Current-Max | 6mA |
| Slew Rate | 2V/μs |
| Architecture | CHOPPER-STAB |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 90pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±1.35V~6V |
| Input Offset Voltage (Vos) | 500nV |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 3000 kHz |
| Average Bias Current-Max (IIB) | 0.003μA |
| Power Supply Rejection Ratio (PSRR) | 120dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 1μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00015μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Neg Supply Voltage-Max (Vsup) | -6V |
| Nominal Gain Bandwidth Product | 3MHz |
| Wideband | NO |
| Voltage Gain-Min | 562000 |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LTC2052HVHS#PBF Overview
There is a 14-SOIC (0.154, 3.90mm Width) case package that contains the instrumentation amplifiers. The instrumentation amplifier in this picture is of the Zero-Drift-type. A Tube case is used for delivering the op amp. The number of terminations approaches 14. There are a total of 14 pins on this op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 14 pins are available on the instrumentation amplifier. In terms of input offset voltage, operational amplifier rates 500nV. This electronic part is recommended for mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureYou can run this op amp ic on 1mA . On this buffer amplifier, there are 4 circuits. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. This linear amplifier has a total of 4 elements. There are a maximum of 562000 voltage gains that can be conducted by this operational amplifier at its minimum voltage gain.
LTC2052HVHS#PBF Features
14 Pins
supply voltage of 5V
Output Type: Rail-to-Rail
LTC2052HVHS#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC2052HVHS#PBF Instrumentational OP Amps applications.
- Home audio systems
- Semiconductor detectors
- Television broadcasting equipment
- Strain gauges
- Medical imaging
- Portable media players
- Non-polarized electrodes
- Vehicle electronics
- Industrial applications including automation
- Television
