LTC2052IGN#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LTC2052 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Elements | 4 |
| Power Supplies | 3/5V |
| Number of Circuits | 4 |
| Operating Supply Current | 850μA |
| Supply Current-Max | 6mA |
| Slew Rate | 2V/μs |
| Architecture | CHOPPER-STAB |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 25pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~7V |
| Input Offset Voltage (Vos) | 500nV |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 140dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Power Supply Rejection Ratio (PSRR) | 120dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 0.5μV |
| Low-Bias | YES |
| Micropower | NO |
| Max Frequency | 7.5kHz |
| Bias Current-Max (IIB) @25C | 0.000075μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5.5V |
| Nominal Gain Bandwidth Product | 3MHz |
| Wideband | NO |
| Height | 1.75mm |
| Length | 4.98mm |
| Width | 3.988mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LTC2052IGN#PBF Overview
In the package, you will find a 16-SSOP (0.154, 3.90mm Width)-case to contain the op amp ic. The instrumentation amplifier in this picture is of the Zero-Drift-type. The case in which buffer amplifier is delivered is called a Tube case. There is a growing number of terminations approaching the number of 16. A total of 16 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 3V battery. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. The op amp ic has an array of 16 pins on it. In terms of the input offset voltage, instrumentation amplifier rates at 500nV. This electrical part should be mounted using type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureOperational amplifier can operate supply current at 850μA. The voltage gain should stay at 140dB. This op amp ic has 4 circuits. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. There are a total of 4 elements in this linear amplifier.
LTC2052IGN#PBF Features
16 Pins
supply voltage of 3V
140dB voltage gain
Output Type: Rail-to-Rail
LTC2052IGN#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC2052IGN#PBF Instrumentational OP Amps applications.
- Test equipment
- Vehicle electronics
- Automotive sensors
- Cinema or auditorium audio system
- Medical imaging
- Displayers for aircraft and air transportation control systems
- Information processing
- Ultrasound transducers
- Switching amplifier
- ECG equipment
