LTC2057HS8#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LTC2057 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Power Supplies | +-2.5/+-30V |
| Number of Circuits | 1 |
| Operating Supply Current | 900μA |
| Slew Rate | 0.45V/μs |
| Architecture | CHOPPER-STAB |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 150 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 4.75V~36V ±2.38V~18V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 500nV |
| Bandwidth | 1.5MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1500 kHz |
| Average Bias Current-Max (IIB) | 0.006μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 20V |
| Voltage - Input Offset | 0.5μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Neg Supply Voltage-Max (Vsup) | -20V |
| Power | NO |
| Length | 4.903mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
LTC2057HS8#PBF Overview
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. Zero-Drift-type instrumentation amplifiers are used in this application. Linear amplifier is delivered in a Tube case. The number of terminations is approaching the 8 mark. In this case, there are 8 pins on the board. I would like to remind you that this buffer op amp should be powered by an 15V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 8 pins are available on the instrumentation amplifier. The input offset voltage is 500nV. This electronic part is recommended for mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureYou can run this op amp ic on 900μA . On this instrumentation amplifier, there are 1 circuits that are connected together. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has.
LTC2057HS8#PBF Features
8 Pins
supply voltage of 15V
Output Type: Rail-to-Rail
LTC2057HS8#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC2057HS8#PBF Instrumentational OP Amps applications.
- Portable media players
- Medical instruments
- Weak signal detection
- Proportional counter tubes
- Exponential operation circuits
- Proportional operation circuits
- Instrumentation
- pH (acidity)
- Test and measurement instruments
- Image computer boards
