LTC3713EG#PBF
| Parameters | |
|---|---|
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LTC3713 |
| Function | Step-Up, Step-Down |
| Number of Outputs | 2 |
| Output Voltage | 36V |
| Output Type | Transistor Driver |
| Max Output Current | 2A |
| Input Voltage-Nom | 15V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 2A |
| Voltage - Supply (Vcc/Vdd) | 1.5V~36V |
| Control Features | Enable, Power Good, Soft Start |
| Input Voltage (Min) | 4V |
| Topology | Buck, Boost |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 1.4MHz |
| Input Voltage (Max) | 30V |
| Synchronous Rectifier | Yes |
| Switcher Configuration | PUSH-PULL |
| Max Frequency | 1.5MHz |
| Duty Cycle (Max) | 90% |
| Clock Sync | No |
| Output Phases | 1 |
| Width | 5.3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | 24-SSOP (0.209, 5.30mm Width) |
| Surface Mount | YES |
| Number of Pins | 24 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Switching Regulator or Controllers |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.65mm |
LTC3713EG#PBF Overview
It comes in a 24-SSOP (0.209, 5.30mm Width) package, so switching controller can be used for most applications. This dc motor controller can be used to generate outputs with 2 numbers. Tube is the solid enclosure in which PMIC is packaged. With Transistor Driver dc switching's output (s), it is able to handle it. 1.5V~36V is the supply voltage and the operating voltage of the dc control. Workable in an dc switcher where -40°C~85°C TA is the -40°C~85°C TArm. A switching controller such as this can switch at a value of 1.4MHz . As it has a Surface Mount value, it can be used for general dc dc regulator. To provide efficient switching control, Enable, Power Good, Soft Start is included in the dcdc regulator. An analog IC with the SWITCHING CONTROLLER signal is connected to the switch converters. There are a terminal (s) on the switching converters that are designed at DUAL. 24 terminations with a variety of function. DC switcher's input voltageis 15V volts. Searching "LTC3713" will return other relevant dc to dc converter ics. The switching converter has a total of 24 pins. The type is a particular Switching Regulator or Controllers of switching converter. Input voltage of dc dc voltage regulator should be 4V. Test statistics indicate DC regulator outputs 36V voltage. Considering the dc to dc regulator can only accept 30V input voltage, it is important to take note of this. If you are starting a new project, you should note the dc dc regulator's typical output current is 2A. It is estimated that this dc regulatorhas a maximum frequency of 1.5MHz. An output current greater than 2A cannot be provided by the dc switcher.
LTC3713EG#PBF Features
Transistor Driver Outputs
Switching Frequency: 1.4MHz
Enable, Power Good, Soft Start
LTC3713EG#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC3713EG#PBF DC to DC converter applications.
- Window air conditioners
- Electrical power transmission
- Motor controller circuits
- Arc suppression circuits
- Automatic plug-in machines
- Milling machines
- Hydraulic presses
- Low output voltage switching power supply circuits
- Planers
- Post equipment
