LTC3864EMSE#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 12-TSSOP (0.118, 3.00mm Width) Exposed Pad |
| Surface Mount | YES |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 12 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | ALSO OPERATES AS LDO REGULATOR |
| Subcategory | Switching Regulator or Controllers |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Terminal Pitch | 0.65mm |
| Base Part Number | LTC3864 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Voltage - Supply (Vcc/Vdd) | 3.5V~60V |
| Control Features | Current Limit, Enable, Frequency Control, Power Good, Soft Start |
| Input Voltage (Min) | 3.5V |
| Topology | Buck |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 50kHz~850kHz |
| Input Voltage (Max) | 60V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Switcher Configuration | SINGLE |
| Duty Cycle (Max) | 100% |
| Length | 4.039mm |
| Width | 3mm |
| RoHS Status | ROHS3 Compliant |
LTC3864EMSE#PBF Overview
This switching controller fits most application requirements since it is packaged in a 12-TSSOP (0.118, 3.00mm Width) Exposed Pad package. For 1 outputs, the dc motor controller is appropriate. PMIC packaging is solid with a Tube enclosure. There are Transistor Driver dc switching's output (s) that it can handle. dc control's supply and operating voltages are 3.5V~60V. Suitable for working in an dc switcher that has a -40°C~125°C TJ. A switching controller such as this can switch at a value of 50kHz~850kHz . As it has a Surface Mount value, it can be used for general dc dc regulator. Current Limit, Enable, Frequency Control, Power Good, Soft Start is used for efficient switching control in the dcdc regulator. Connected to a SWITCHING CONTROLLER analog IC, the switch converters are connected to a power supply. Switching converters are designed with the terminal (s) at position DUAL . A variety of 12 terminations are available in dc switching. A few of the control techniques these dc dc converter ics adapt include PULSE WIDTH MODULATION. DC switcher's input voltageis 12V volts. LTC3864 can be searched for other relevant dc to dc converter ics. Specifically, switching converter falls under the Switching Regulator or Controllers category. An input voltage of 3.5V is the minimum required for the dc dc voltage regulator. This dc to dc regulator accepts only 60V input voltage at most. To better satisfy the need, DC to DC voltage regulator has a value of ALSO OPERATES AS LDO REGULATOR.
LTC3864EMSE#PBF Features
Transistor Driver Outputs
Switching Frequency: 50kHz~850kHz
Current Limit, Enable, Frequency Control, Power Good, Soft Start
PULSE WIDTH MODULATION
ALSO OPERATES AS LDO REGULATOR
LTC3864EMSE#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC3864EMSE#PBF DC to DC converter applications.
- Experimental setup
- Post equipment
- Machining centers
- Printing equipment
- Low output voltage switching power supply circuits
- Flaw detection equipment
- Current source circuits
- Servo drive system
- Access control systems
- Motor controller circuits
