LTC3864HDE#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 12-WFDFN Exposed Pad |
| Surface Mount | YES |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 12 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | ALSO OPERATES AS LDO REGULATOR |
| Subcategory | Switching Regulator or Controllers |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Pitch | 0.5mm |
| Base Part Number | LTC3864 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Voltage - Supply (Vcc/Vdd) | 3.5V~60V |
| Control Features | Current Limit, Enable, Frequency Control, Power Good, Soft Start |
| Input Voltage (Min) | 3.5V |
| Topology | Buck |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 50kHz~850kHz |
| Input Voltage (Max) | 60V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Switcher Configuration | SINGLE |
| Duty Cycle (Max) | 100% |
| Height Seated (Max) | 0.8mm |
| Length | 4mm |
| Width | 3mm |
| RoHS Status | ROHS3 Compliant |
LTC3864HDE#PBF Overview
With its 12-WFDFN Exposed Pad package, the switching controller fits the needs of most applications. 1 outputs can be generated with the dc motor controller. An enclosure of Tube is used to package the PMIC. Transistor Driver dc switching's outputs (s) can be handled by it. This dc control has a supply voltage and operating voltage of 3.5V~60V. Qualified to work in an dc switcher with -40°C~150°C TJ. In this switching controller, the switch can be set to 50kHz~850kHz. dc dc regulators can be carried out with Surface Mount. Current Limit, Enable, Frequency Control, Power Good, Soft Start is used for efficient switching control in the dcdc regulator. Connected to a SWITCHING CONTROLLER analog IC, the switch converters are connected to a power supply. A switching converters's terminal (s) sits at the DUAL position. A variety of dc switching's functions can be performed on 12 terminations. These dc dc converter ics adapt several control methods, including PULSE WIDTH MODULATION. DC switcher's input voltageis 12V volts. In addition to "LTC3864", there are other relevant dc to dc converter ics you can find. Specifically, switching converter falls under the Switching Regulator or Controllers category. It is recommended that the dc dc voltage regulator's minimum input voltage be 3.5V. Voltages 60V are the maximum that the dc to dc regulator will accept. DC to DC voltage regulator has the value of ALSO OPERATES AS LDO REGULATOR to better satisfy the requirement.
LTC3864HDE#PBF Features
Transistor Driver Outputs
Switching Frequency: 50kHz~850kHz
Current Limit, Enable, Frequency Control, Power Good, Soft Start
PULSE WIDTH MODULATION
ALSO OPERATES AS LDO REGULATOR
LTC3864HDE#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC3864HDE#PBF DC to DC converter applications.
- Electrical power transmission
- ATMs
- Remotely powered electric motors
- Scientific research
- Large fire protection systems
- Die casting equipment
- Driver circuits
- Power supplies of electronic gadgets
- Wind power
- Bending machines
