LTC6078ACMS8#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LTC6078 |
| Pin Count | 8 |
| JESD-30 Code | S-PDSO-G8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Circuits | 2 |
| Current - Supply | 55μA |
| Slew Rate | 0.05V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 103 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Gain Bandwidth Product | 750kHz |
| Unity Gain BW-Nom | 750 kHz |
| Average Bias Current-Max (IIB) | 0.00005μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 10μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.000001μA |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
LTC6078ACMS8#PBF Overview
It is packaged in an 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case that protects the operational amplifiers from damage. Op amps are General Purpose types of amplifier on the chip. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. The number of terminations approaches 8. There are a total of 8 pins on this op amp. I would like to remind you that this buffer op amp should be powered by an 3V battery. It should be noted that this op amp is a type of Operational Amplifier device. This electronic part is best mounted with type Surface Mount. According to the manufacturer, this buffer op amp works well at 0°C~70°C , which is a good operating temperature. A instrumentation amplifier like this has 2 circuits. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. There is a recommendation that this electrical part be used with a supply with 55μA current rating.
LTC6078ACMS8#PBF Features
8 Pins
supply voltage of 3V
Output Type: Rail-to-Rail
LTC6078ACMS8#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC6078ACMS8#PBF Instrumentational OP Amps applications.
- Logarithmic operation circuits
- Power control
- High/low-pass filter circuit
- Switching amplifier
- High-frequency data acquisition systems
- Blood pressure sensors
- Signal operation
- RF cable systems
- Test and measurement instruments
- Test equipment
