LTC6078HMS8#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LTC6078 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Operating Supply Current | 55μA |
| Slew Rate | 0.05V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 91 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 25mA |
| Input Offset Voltage (Vos) | 7μV |
| Bandwidth | 780 kHz |
| Unity Gain BW-Nom | 750 kHz |
| Voltage Gain | 125dB |
| Average Bias Current-Max (IIB) | 0.00035μA |
| Power Supply Rejection Ratio (PSRR) | 120dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 10μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.000001μA |
| Nominal Gain Bandwidth Product | 750 kHz |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LTC6078HMS8#PBF Overview
Op amp is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case. This is a General Purpose type op amp. The op amp is delivered to you in a Tube case. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are attached to buffer op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 3V. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. 8 pins are located on the operational amplifiers. Regarding input offset voltage, op amp rates 7μV. For this electronic part, it is recommended that you mount it with type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. The buffer amplifier is capable of operating from a supply current of 55μA . Op amp is a member of the 125dB's 125dB family. A linear amplifier like this has 2 circuits on it. There are a total of 2 channels available on the op amps. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals.
LTC6078HMS8#PBF Features
8 Pins
supply voltage of 3V
125dB voltage gain
Output Type: Rail-to-Rail
LTC6078HMS8#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC6078HMS8#PBF Instrumentational OP Amps applications.
- Signal amplification
- Differentiator circuits
- single/dual op amp sum and difference circuits
- Addition operation circuits
- Medical imaging
- Power transmission
- Exponential operation circuits
- Proportional counter tubes
- Weak signal detection
- Test equipment
