LTC6081IDD#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-WFDFN Exposed Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2010 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LTC6081 |
| Pin Count | 10 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Power Supplies | 3/5V |
| Number of Circuits | 2 |
| Operating Supply Current | 340μA |
| Supply Current-Max | 0.93mA |
| Slew Rate | 1V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 24mA |
| Input Offset Voltage (Vos) | 70μV |
| Bandwidth | 3.6MHz |
| Gain Bandwidth Product | 3.5MHz |
| Unity Gain BW-Nom | 3600 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.00004μA |
| Power Supply Rejection Ratio (PSRR) | 98dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.000001μA |
| Programmable Power | NO |
| Height Seated (Max) | 0.8mm |
| Length | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
LTC6081IDD#PBF Overview
It is packaged in an 10-WFDFN Exposed Pad-case that protects the operational amplifiers from damage. Buffer amps of this type are called General Purpose-types. Instrumentation amplifier is delivered in a Tube case. There have been a total of 10 terminations over the past year. The pins on this board total to 10 in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 3V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 10 pins are available on the instrumentation amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 70μV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~85°C. In order for this instrumentation amplifier to operate, the supply current needs to be between 340μA and 10 . The voltage gain should stay at 120dB. This op amp contains 2 circuits. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. It is possible to count 2 elements on this buffer amplifier.
LTC6081IDD#PBF Features
10 Pins
supply voltage of 3V
120dB voltage gain
Output Type: Rail-to-Rail
LTC6081IDD#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC6081IDD#PBF Instrumentational OP Amps applications.
- Navigation
- High-frequency data acquisition systems
- Proportional counter tubes
- Biopotential
- Blood pressure sensors
- Integrator circuits
- Inverse/same-phase proportional circuit
- Band-stop filter
- Signal amplification
- Differentiator circuits
