LTC6090IS8E#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) Exposed Pad |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2014 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LTC6090 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Power Supplies | +-70V |
| Number of Circuits | 1 |
| Current - Supply | 2.8mA |
| Slew Rate | 21V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 140 dB |
| Current - Input Bias | 3pA |
| Voltage - Supply, Single/Dual (±) | 9.5V~140V ±4.75V~70V |
| Gain Bandwidth Product | 12MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 12000 kHz |
| Average Bias Current-Max (IIB) | 0.00005μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 75V |
| Voltage - Input Offset | 330μV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Neg Supply Voltage-Max (Vsup) | -75V |
| Wideband | NO |
| Power | NO |
| Voltage Gain-Min | 400000 |
| Length | 4.9025mm |
| RoHS Status | ROHS3 Compliant |
LTC6090IS8E#PBF Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) Exposed Pad case, the buffer op amp is ready to use. The instrumentation amplifier in this picture is of the General Purpose-type. In the case of Tube cases, linear amplifier will be delivered. During the past two weeks, there have been close to 8 terminations. In this case, there are 8 pins on the board. This linear amplifier should be powered by an 15V battery. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. A instrumentation amplifier like this has 1 circuits. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. As a result, it is recommended that a power supply of 2.8mA be used with this electronic part. The minimum voltage gain this buffer op amp is able to conduct is 400000.
LTC6090IS8E#PBF Features
8 Pins
supply voltage of 15V
Output Type: Rail-to-Rail
LTC6090IS8E#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC6090IS8E#PBF Instrumentational OP Amps applications.
- Television broadcasting equipment
- Displayers for aircraft and air transportation control systems
- Subtraction operation circuits
- earphone
- Video conversion and routing
- Image computer boards
- PDA
- Video data acquisition
- Integrator circuits
- Power generator
