LTC6241HS8#TRPBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LTC6241 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Power Supplies | 3/5V |
| Operating Supply Current | 1.8mA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 78 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 2.8V~6V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 40μV |
| Gain Bandwidth Product | 18MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 124.08dB |
| Average Bias Current-Max (IIB) | 0.0015μA |
| Power Supply Rejection Ratio (PSRR) | 78dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 18MHz |
| Wideband | NO |
| Length | 4.9mm |
| RoHS Status | ROHS3 Compliant |
LTC6241HS8#TRPBF Overview
There is a 8-SOIC (0.154, 3.90mm Width) case package that contains the instrumentation amplifiers. A General Purpose-type buffer amplifier is shown here. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. In recent months, the number of terminations has approached 8. In this case, there are 8 pins on the board. It would be helpful if you could remember that this op amp ic should be powered by an 3V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. The op amp ic has an array of 8 pins on it. Op amp ic rates 40μV for input offset voltage. For this electrical component, Surface Mount is the recommended mounting type. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. As long as the supply current of the chip does not exceed 1.8mA, this op amp ic can operate. Maintain 124.08dB as the voltage gain. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. There are 2 elements in this buffer amplifier. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted.
LTC6241HS8#TRPBF Features
8 Pins
supply voltage of 3V
124.08dB voltage gain
Output Type: Rail-to-Rail
LTC6241HS8#TRPBF Applications
There are a lot of Linear Technology/Analog Devices LTC6241HS8#TRPBF Instrumentational OP Amps applications.
- Mobile phone
- Power transmission
- Commercial audio systems
- Oscilloscopes
- Instrumentation
- Automation control systems
- Video amplifiers
- Medical imaging
- Image computer boards
- Proportional operation circuits
